Abstract:Abstract A radiofrequency (RF) ion source with a megawatt power extraction, thunder I, has been developed for the neutral beam injector (NBI) on HL-2A tokamak. A full solid-state RF generator with output power of 80 kW and frequency of 2 MHz was built by an RF combiner using 8 modules of solid-state RF generator with power of P RF = 10 kW. The line electric efficiency of whole RF generator reaches 92% and its voltage standing wave ratio (VSWR) is 1.01, thus no water-cooling system is supplied. A quartz vessel with the inner diameter of 250 mm is directly adopted for resisting atmospheric pressure, which can dramatically simplify source structure. Nowadays, the extracted beam parameters of RF hydrogen ion source are 32 kV/20 A/0.1 s on a test bed, while the design parameters are 50 kV/20 A/3 s. The beam density profile measured by the infrared imaging technique at 1.3 m downstream from the grounded grid obeys a Gaussian distribution, and the corresponding half width of 1/ e power decay at the matched condition is about 80 mm. Plasma homogeneity is over 90% at low RF power. The beam divergence angle meets the requirement of NBI system on HL-2A tokamak. The extractable current density increases almost linearly with the RF power. It reaches 2400 A m −2 at P RF = 32 kW. The ion density in front of plasma grid is about 1 × 10 18 m −3 , corresponding to an ionized fraction of about 1% at the gas pressure of 0.5 Pa. Single hydrogen ion fraction reaches 79% at the beam current of 12.4 A. Some improvements have been considered for optimizing ion source performance on next experimental campaign. One smaller auxiliary RF discharge chamber equipped with a gas feed path, driven by 13.56 MHz/3.5 kW generator, is connected to main discharge chamber driven by 2 MHz/40 kW generator. By this dual-driven configuration, the innovative RF plasma source with high-pressure density gradient solves the initial ignition problem of powerful RF ion source even if the gas pressure below 0.1 Pa. In addition, the RF negative hydrogen ion source of 200 kV/20 A/3600 s is also developed at SWIP for the China fusion engineering test reactor.

Design Study of Primary Ion Provider for Relativistic Heavy Ion Collider Electron Beam Ion Source

Physics design of phase and energy adjustment for heavy ion beam of the same mass with two-charge state on BISOL

Optically Pumped Polarized $^3$He$^{++}$ Ion Source Development for RHIC/EIC

Design of a Beam Line for Simultaneous Dual-Beam Ion Implantation

Design and Optimization Study of a Duoplasmatron Ion Source for High-Intensity Proton Beam

Design Study of Multi-Charge Low Energy Beams Transport for BISOL Post Accelerator

Status of the Los Alamos heavy ion injector

High Performance Charge Breeder for HIE-ISOLDE and TSR@ISOLDE Applications

[Risk factors associated with invasive fungal infection in orthotopic liver transplantation].

Production of High-Intensity, Highly Charged Ions

Beam dynamics study of the high-power electron beam irradiator using niobium-tin superconducting cavity

Preliminary Design of a Hybrid Ion Source for 7li3+ Generation

A 2.45 Ghz Electron Cyclotron Resonance Proton Ion Source and A Dual-Lens Low Energy Beam Transport

Use of the Internet for teaching in nuclear medicine.

DESIGN OF AN L-BAND RF PHOTOINJECTOR FOR THE IDAHO ACCELERATOR CENTER 44 MeV LINAC

Development of a 50 kV hydrogen–helium mixed ion beam implanter

Feasibility Study on the Use of a Superconducting Synchrocyclotron and Electron Beam Ion Source for Heavy-Ion Therapy

Beam Formation Studies on the CERN IS03b H Source

Development of megawatt radiofrequency ion source for the neutral beam injector on HL-2A tokamak

Investigation of High Duty Factor Isr Rfq-1000

Polyatomic ions from a high current ion implanter driven by a liquid metal ion source