Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

High Efficiency of Flexible Polymer Solar Cell Based on Poly(3- Hexylthiophene)/fullerene

High Performance Solar Cell Based on Ultra-Thin Poly(3-Hexylthiophene): Fullerene Film Without Thermal and Solvent Annealing

Highly Flexible All‐Polymer Solar Cells Processed Without Post‐Treatment Achieving 13.56% Efficiency

Efficient Polymer Solar Cells with Thin Active Layers Based on Alternating Polyfluorene Copolymer/Fullerene Bulk Heterojunctions

Highly Efficient Polymer Tandem Cells and Semitransparent Cells for Solar Energy

Enhanced power-conversion efficiency in polymer solar cells using an inverted device structure

Electric Field-Assisted Self-Organization of Polymer:Fullerene Hybrids on the Photovoltaic Performance

Enhanced Efficiency Of Polymer: Fullerene Bulk Heterojunction Solar Cells With The Insertion Of Thin Tio2

High-performance inverted polymer solar cells: Device characterization, optical modeling, and hole-transporting modifications

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Efficient Low-Cost All-Flexible Microcavity Semitransparent Polymer Solar Cells Enabled by Polymer Flexible One-Dimensional Photonic Crystals.

Highly Efficient Flexible Perovskite Solar Cells on PET films via Dual Halide and Low‐Dimensional Interface Engineering for Indoor Photovoltaics

Surpassing 13% Efficiency for Polythiophene Organic Solar Cells Processed from Nonhalogenated Solvent

Improvement in Power Conversion Efficiency of All-Polymer Solar Cells Enabled by Ultrafast Channels for Charge Dynamics

Highly Efficient Solar Cells Based on the Copolymer of Benzodithiophene and Thienopyrroledione with Solvent Annealing

Efficient conventional- and inverted-type photovoltaic cells using a planar alternating polythiophene copolymer

A Planar Electron Acceptor for Efficient Polymer Solar Cells

Nonhalogenated‐Solvent‐Processed High‐Performance All‐Polymer Solar Cell with Efficiency over 14%

High-performance fullerene-free polymer solar cells with 6.31% efficiency

All-polymer Solar Cells Based on Side-Chain-isolated Polythiophenes and Poly(perylene Diimide-Alt-dithienothiophene)

A Versatile Fluoro‐Containing Low‐Bandgap Polymer for Efficient Semitransparent and Tandem Polymer Solar Cells