Test of SiC-electrodes in a high current pseudospark switch

andreas gortler,a schwandner,k frank,j christiansen,d h h hoffmann

DOI: https://doi.org/10.1109/PLASMA.1995.533550

1995-01-01

Abstract:Summary form only given. The electrode erosion is a limiting factor in the lifetime of pseudospark switches. Mainly in high current applications (30 kA

What problem does this paper attempt to address?

Electrode Phenomena and Measurements of the Erosion Rate in High-Current Pseudospark-Switches

U Prucker,J Christiansen,K Frank,A Gortler,DHH Hoffmann,A Schwandner,R Tkotz

DOI: https://doi.org/10.1109/27.640698

IF: 1.368

1997-01-01

IEEE Transactions on Plasma Science

Abstract:For microsecond pulses and peak currents up to 105 kA, the erosion rate and the discharge behaviour of molybdenum electrodes was investigated. A contraction of the plasma column occurs at the cathode for peak currents above 20 kA, as indicated by streak photography. A bright luminous anode flare appears at a peak current of about 40 kA, correlated with an evident anode melting. A further constriction of the anode flare was observed for currents exceeding 90 kA. In opposition to lower currents, an increase in weight of the cathode was also noticed
Sealed-off Pseudospark Switches for Pulsed Power

K Frank,C Bickes,U Ernst,M Iberler,J Meier,U Prucker,M Schlaug,J Schwab,J Urban,DHH Hoffmann

DOI: https://doi.org/10.1109/ppc.1997.679339

1997-01-01

Abstract:There has been a considerable progress in understanding the physics and technology of high power pseudospark switches, which allows their implementation in pulsed power applications. These switches have very wide dynamic range of breakdown voltage operation: from 1% to 99%. Single-gap systems still have the disadvantage of small hold-off voltage, which is lower than 25 kV and which requires the construction of two-stage systems. In this way, a more reliable hold-off voltage as high as 30 kV would be achieved. Based upon a better understanding of fundamental discharge processes, it is possible to suppress the quenching phenomenon. This might prove helpful in some pulsed power applications. Semiconductor electrode materials are the best choice for devices with considerably reduced electrode erosion and prevention from statistically distributed drop of impedance. The feasibility of a durable composite of semiconductor and metallic bath electrode will facilitate tremendously the construction of sealed-off pseudospark switches for pulsed power applications, especially to replace ignitron and spark gaps. Up to now, the tested prototypes operate with hold-off voltages up to 20 kV, peak currents up to 150 kA and pulse length up to 20 /spl mu/s. Tests with longer pulse length are planned in order to extend the commercial applicability of these devices.
Reliability Analysis for Commercial SiC MOSFETs in Single Pulse and Repetitive Surge Current Test

Hao Wu,Chunyan Jiang,Qing Guo,Na Ren,Zhengyun Zhu,Bin Wu,Xiang Qi

DOI: https://doi.org/10.1109/phm-jinan48558.2020.00093

2020-01-01

Abstract:SiC MOSFET Body diodes are expected to compete against SiC schottky barrier diodes (SBD) in high power applications. To investigate the surge capability of the body diodes in commercial SiC MOSFETs, single pulse and repetitive surge current tests are processed on the DUTs. In single pulse surge current test, the DUTs are stressed to failure. Compared with the body diodes in SiC trench-gate MOSFETs, the body diodes in SiC planar-gate MOSFETs tend to show better surge capability at all rated current levels. On the other hand, in repetitive surge current test, the degradation of electrical parameters is observed after hundreds of pulse cycles. The degradation mechanism of bipolar degradation and oxide layer degradation has been analyzed.
Scientific and Technological Progress of Pseudospark Devices

K Frank,C Bickes,E Dewald,U Ernst,M Iberler,J Meier,U Prucker,A Rainer,M Schlaug,J Schwab,J Urban,W Weisser,DHH Hoffmann

DOI: https://doi.org/10.1109/deiv.1998.740646

IF: 1.368

1999-01-01

IEEE Transactions on Plasma Science

Abstract:The paper presents an overview on the state-of-the-art of research and development with pseudospark devices (low pressure gas discharge device). Based on the pseudospark geometry several modified configurations were developed like the channel spark and the preionization-controlled open-ended hollow cathode system. In pulsed electrical circuits for discharge currents below 10 kA distinct discharge phenomena appear which have to be suppressed for any application. One is transient impedance transitions correlated with steps in forward voltage drop. By geometry and choice of electrode material the irregular transitions in impedance can be controlled over a wide parameter range. Another is quenching, observed as a random effect, which is influenced by many parameters. Results from the experiment indicate that quenching is strongly dependent on the number density of gas atoms of gas atoms in the discharge volume. Since silicon carbide (SiC) as part of the switch electrode downsizes the quenching current to negligible values (<1 kA) optical spectroscopy was used to investigate the influence of this semiconducting material on the temporal development of the discharge, by looking for emission lines of the released silicon and/or carbon atoms. The technological aspects of pseudospark devices naturally are to achieve higher lifetime and improved overall reliability. Multichannel configurations and two-gap systems are under development to reduce erosion rate and to increase hold-off capability, respectively. Under clean conditions a hold-off voltage of 65 kV was realized by a two-gap system.
Interferometric measurement of the electron density in a pseudospark switch

andreas gortler,a schwandner,k frank,j christiansen,d h h hoffmann

DOI: https://doi.org/10.1109/PLASMA.1995.532795

1995-01-01

Abstract:Summary form only given. In the recent years pseudospark switches have been developed for several applications in pulsed power devices. The pseudospark is a low pressure gas discharge usable as a closing switch. For medium power (I<30 kA, pulse length<500 ns) sealed-off devices are available for tests. In the high current regime (currents>30 kA up to a few 100 kA, pulse length<20 /spl mu/s) only devices connected to a vacuum system are in use. The pseudospark transforms from a special hollow cathode discharge to a metal vapour arc like discharge type when the current exceeds 35 kA. Fast shutter photographs of the discharge prove the appearance of filaments at currents exceeding 40 kA corresponding to a dip in the forward voltage drop and a rise of the erosion rate of about one order of magnitude (4 to 40 /spl mu/g/C) for molybdenum electrodes. The knowledge of the electron density distribution provides more information about these phenomena The discharge is no more radial symmetric to the central apertures at these high currents. A contraction to a small area on the plane electrode surface takes place. Therefore a tomographic setup is necessary to measure the electron density distribution with interferometry. To eliminate the contribution of the ions and the neutral plasma particles to the phase shifts two wavelengths are necessary.
Effect of Different Electrode Materials on Electrode Erosion Characteristics and Failure Modes of Gas Spark Switch

Jiawei Wu,Ruoyu Han,Qiaojue Liu,Yan Jing,Yanan Wang,Aici Qiu

DOI: https://doi.org/10.1109/plasma.2015.7179658

2015-01-01

Abstract:Summary form only given. As one of the key components in the pulsed power system, the two-electrode gas spark switch has many advantages such aslarge charge transfer, high current capability, stability and long lifetime. But some practical engineering issues, like the extraction of unconventional gas resources, set strictly demands on switch's work environment and output characteristics, such as high current capability, high breakdown voltage stability, long lifetime, high-frequency operation while working in a small airtight chamber without gas blowing system. The performances of the switch directly influence the output characteristics of the system. The electrode erosion of electrodes caused by high current directly influences the performances of the switch. But few studies have done on the effect of different electrode materials on electrode erosion characteristics and failure modes of gas spark switch. Analyses of the physical characteristics and chemical characteristics of different electrodes' surfaces at different stage of life were shown. By analysing the erosion characteristics and special failure phenomenon of electrodes, some relationships between different electrode materials and failure modes were proposed. to investigate the Cu-W (90 wt%) two-electrode spark-gap switch working in an airtight cavity (1.18 L) without gas blowing system. A test stand was established and could been divided into five parts, a DC power, a pulse capacitor, a two-electrode gas spark switch, a low inductance load resistor and measurement systems. The gas spark switch was working in an airtight cavity (1.18 L) without gas blowing system. The switch was tested with frequency of 0.1 Hz, self-breakdown voltage of 30 kV, peak current of 50 kA. A scanning electron microscope and a Dynamic 3D aspheric profiler were used to observe the surface roughness of the electrodes. A Bruker Tensor 27 FT-IR Spectrometer and an X-ray photoelectron spectroscopy were used to analyze the chemical composition of erosion product.
Long Lifetime, Triggered, Spark-Gap Switch For Repetitive Pulsed Power Applications

Gjj Winands,Z Liu,Ajm Pemen,Ejm Van Heesch,K Yan

DOI: https://doi.org/10.1063/1.2008047

IF: 1.6

2005-01-01

Review of Scientific Instruments

Abstract:In this article a critical component for pulsed power applications is described: the heavy-duty switch. The design of a coaxial, high repetition rate, large average power, and long lifetime spark-gap switch is discussed. The switch is used with a fail-free LCR trigger circuit. Critical issues for switch design are presented together with experimental results. It is observed that the switch has a good stability, and its lifetime is estimated to be in the order of 10(10) shots (similar to 10(6) C) at 10 J/pulse, 60 kV and 100 ns pulses. Measurements were performed with 20 and 34 kV average switching voltage (100 ns pulses, energy per pulse 0.4 and 0.75 J, respectively). For up to 450 pulses/s (pps), pre-firing can be prevented by increasing the gap pressure (up to 2.5 and 7 bars, respectively), no gas flush is required. Above 450 pps, up to 820 pps, a forced gas flow of maximal 35 Nm(3)/h, is required for stable operation. Measurements on the time delay and jitter of the switch demonstrate that these values are influenced by pressure, flow, and pulse repetition rate. For 34 kV average switching voltage the time delay and time jitter vary between 35 and 250 and 10 and 80 mu s, respectively. For 20 kV average switching voltage these values are: 30-160 and 4-50 mu s. During a test run of 2.5 h (at 100 Hz, 0.75 J/pulse) the feasibility of the switch was proved, and the switching voltage jitter was less than 0.7%. (c) 2005 American Institute of Physics.
Characteristics of pseudospark switches for pulsed power modulators

k frank,j christiansen,s dollinger,p felsner,andreas gortler,f heine,g hintz,d h h hoffmann,u prucker,a schwandner

DOI: https://doi.org/10.1109/MODSYM.1996.564468

1996-01-01

Abstract:Pseudospark switches (PSS) are considered to be an alternative not only to thyratrons or medium-power spark gaps but also to ignitrons. A lifetime of more than 108 discharges with a corresponding total charge transfer of 600 kC was achieved in laser circuits. Electrode erosion is still the main limiting factor to make high power PSS a serious competitor to commercially available switches. One approach to solve this problem is to distribute the total current on several discharge channels with a common hollow cathode. The other one is to look for suitable electrode materials or compounds of them. In order to distribute the discharge homogeneously over more than one single channel synchronous triggering of all channels is indispensable. The trigger method used is a pulsed glow discharge. The characteristics of the trigger discharge as a function of delay and jitter was investigated in combination with actual triggering of all channels. After successful triggering of all channels the corresponding current filaments try to pinch by self-magnetic fields. For long current pulses (i.e. more than 1 or 2 μs for a 80 kA peak current) a single plasma column develops in the symmetry axis of the device. Streak photographs allow determination of pinch time as a function of the peak current, the number of channels, the gap distance and so on. A better understanding of electrode phenomena is essential in order to improve PSSs to carry high peak currents and simultaneously allow high charge transfer. The critical current density at which electrode erosion dramatically rises is still an unknown parameter
Multiple-Gap Spark Gap Switch

Z. Liu,K. Yan,G. J. J. Winands,A. J. M. Pemen,E. J. M. Van Heesch,D. B. Pawelek

DOI: https://doi.org/10.1063/1.2216792

IF: 1.6

2006-01-01

Review of Scientific Instruments

Abstract:A triggered multiple-gap spark gap switch has been developed and tested under atmosphere. By means of an LCR trigger circuit, the multiple-gap switch can be used very reliably. For the same switching voltage (35.5kV), with increasing the number of gaps from 2 to 6, the switching current rise time is reduced from 13.5to6ns, and the energy efficiency is increased from 87% to 92%. An eight-gap switch was also tested, and the switching current rise time is much smaller than the usable rise time of the current probe (3.5ns). One interesting application of the multiple-gap switch is to improve the switching performance in the multiple-switch and transmission lines based pulsed power circuit. To verify this application, a six-gap switch was tested. In contrast to a single-gap switch, the output current rise time was improved from 21to11ns by the six-gap switch.
Design and Performance Analysis of Multi-gap Multi-channel Spark Switch with LCR Triggered Method

ZHANG Zhicheng,ZHANG Xuming,ZHENG Chao,DENG Guanlei,YAN Keping,LIU Zhen

DOI: https://doi.org/10.3969/j.issn.1003-6520.2013.04.024

2013-01-01

Abstract:In order to experimentally research electrical fragmentation of rocks and plasma sterilization,we developed an LCR-triggered,multi-gap,and multi-channel switch.The short pulsed forming switch was formed by the spark switch,of which a group of ceramic capacitors of low inductance in coaxial configuration was charged by a μs primary pulsed power supply.The switch performance was tested with a resistor of 600 Ω,and was further tested by an experiment of sterilization which adopted a pulse power supply.Experimental results showed that the switch had switch-on voltage in range of 29~45 kV while its total gap distance was 14 mm;when the operating voltage was 34 kV,the averaged switch-on time delay and jittering time were 115 μs and 71 μs,respectively.In the test with the resistor,the peak power on the resistor was 1.776 MW,and the range of amplitude and the rise time of the output voltages on the resistor were 33.4~34 kV and 23~28 ns,respectively.The total switch energy loss was 8%,and the energy loss on triggered circuit was 2.163 %.After 2.5×104 shots of switching,the electrode erosion was uniform,and the lengths of the electrodes were unchanged.The output amplitude voltages on the load of continuous 20 times of switching of the spark switch in the presence and absence of LCR triggered circuits were examined.The results show that adopting the LCR triggered circuit has greatly improved the switching stability of the spark switch.
The effect of intermediate electrode on pseudo-spark switch performance with high repetition rate

B. H. Hamad,A. K. Ahmad

DOI: https://doi.org/10.1007/s00202-021-01319-0

IF: 1.63

2021-06-10

Electrical Engineering

Abstract:The present research focuses on the characteristics of a two-stage pseudo-spark switch (PSS). In this project, the pseudo-spark chamber contains three identical electrodes constructed from a stainless-steel material isolated by a glazed ceramic material used as an insulator, with 0.07 m in diameter and 0.003 m in thickness. A pseudo-spark switch of ~ 30 kV anode voltages, 24 kA with 5 ns current rise time and a repetition rate of 160 kHz has been constructed and used effectively. A trigger circuit is designed, constructed and successfully used in a multi-shot mode with high repetition rate; this operation produces a 2.1-kV, 2-μs trigger pulse in width, which is sufficient to provoke and breakdown the argon gas within the cathode. Such a switch has jitter time between pulses less than 8 ns and 8 × 10<sup>11</sup>A/s rise time rate at a working argon gas pressure 0.3 mbar. The intermediate electrode gives us a high-power switch, which has many applications in medical techniques and in discharge heated copper vapor laser applications. The PSS system lifetime is reliant on the electrodes material type and on insulator material used in the main gap of the PSS.

engineering, electrical & electronic
Influence of metal vapour release on pseudospark switch performance

n achterberg,p felsner,klaus frank,andreas gortler,g hintz,t mehr,j stenzenberger,m stetter,r tkotz,j chrisansen,d h h hoffmann

DOI: https://doi.org/10.1109/PLASMA.1995.533551

1995-01-01

Abstract:Summary form only given. The pseudospark discharge is a low pressure (10-100 Pa of hydrogen or helium) gas discharge in a coaxial electrode geometry. Both, cathode and anode are built as hollow electrodes and have a central bore. For the use as a fast closing switch at least 10/sup 9/ electrons have to be injected into the hollow cathode to ignite the discharge with low timing jitter. Within some tens of nanoseconds the discharge runs through different modes and the switch impedance drops to very low values. A typical pseudospark switch (3 mm electrode distance, 3 mm electrode holes, 4 mm electrode thickness) was run in a circuit with low current rise (10/sup 9/ A/s) to prolong the discharge phases. Different investigations (spectrally resolved fast shutter photography and photo multiplier measurements, determination of the electron beam passing into the hollow anode by a Faraday cup, measurement of the forward voltage drop FVD by two high voltage probes) were performed. Results of these measurements are compared to quantitative measurements of the metal vapour density by laser induced fluorescence. Possible mechanisms of the different discharge phases are discussed.
Low-Pressure Pseudospark Switches for Icf Pulsed Power

K Frank,C Bickes,U Ernst,M Iberler,J Meier,U Prucker,M Schlaug,J Schwab,J Urban,DHH Hoffmann

DOI: https://doi.org/10.1016/s0168-9002(98)00403-3

1998-01-01

Abstract:Hollow-electrode pseudospark switches are gas-filled, low-pressure, high-current plasma switches which are based on cold cathode emission. They have the capability to satisfy at least a part of switching requirements for different applications in ICF drivers. The main purpose of the submitted paper is therefore to discuss the following realistic ways for the use of pseudospark switches. There are intense international activities aimed at investigating different approaches for the ignition of an ICF capsule. Most of these efforts utilize lasers of varying wavelengths to deliver the energy to initiate the ablation of the target, the compression and ignition of the fuel, and the propagation of the fusion burn. One alternative to this scheme is to provide the drive energy in form of a light ion beam produced by an efficient pulse power accelerator. A related method uses beams of heavy ion beams from high intensity versions of traditional high-energy accelerators. Dependent on the ICF driver for the power conditioning unit (PCU) arise totally different demands. These extremely different requirements mainly rely on the very specific character of the load. Flashlamps, pumping high power lasers represent a non-linear, low-impedance load. Relatively low switching voltage is necessary, but a high charge-transfer capability. Induction cells or magnetic compression units have a high impedance. Consequently high voltage (up to several 100kV) is required to feed the energy in Marx modules and the following voltage adders produce megavolt voltages, which determines likewise the specific data of the used switch.
Experimental Study of Electrode Erosion and Aging Process of a Specially Designed Gas Switch under Repetitive Arc Discharge

Jiawei Wu,Ruoyu Han,Weidong Ding,Aici Qiu

DOI: https://doi.org/10.1109/tdei.2017.006254

IF: 2.509

2017-01-01

IEEE Transactions on Dielectrics and Electrical Insulation

Abstract:In this paper, a study concerning self-breakdown voltage characteristics, electrode erosion, and degradation of the insulator, of a two-electrode spark-gap switch has been presented based on experiments. A 6 mu F pulse capacitor and a DC high voltage source (set at -40 kV) were utilized to achieve similar to 0.1 pulses per second repetitive arc discharge between two fixed Cu-W (Cu30/W70) alloy electrodes in the 1.2 L airtight chamber of the switch. With average transfer charge of 2.2 C per shot, this switch was tested for 5800 shots altogether. The results demonstrated the electrode erosion rate of the cathode was 6.3434x10(-6) cm(3)/C whereas that of anode was 5.4691x10(-6) cm(3)/C. Besides, by analyzing electrode surfaces' morphology and PTFE insulator surfaces' compositions after 5800 shots with the help of a scanning electron microscope, a dynamic 3D aspheric metrology instrument, an X-ray photoelectron spectrometer, a metallographic microscope, and a Mettler-Toledo analytical balance, some evidence of physical processes and chemical reactions between plasma channel, electrode materials, and insulation materials could be observed. Moreover, the chamber was opened and inspected for 10 times during the whole procedure, thus providing an overall description of the variation of the switch. It should also be pointed out that owing to complex mechanisms during the aging process, the self-breakdown voltage followed a mixed Normal distribution other than any other simple distributions.
Surface Morphology of Cu-W Alloy Electrodes in a Long Lifetime Gas Spark Switch

Jiawei WU,Ruoyu HAN,Weidong DING,Haibin ZHOU,Aici QIU

DOI: https://doi.org/10.13334/j.0258-8013.pcsee.160442

2017-01-01

Abstract:Considering the complex circumstances in real applications such as the underground mine environment, the gas switch is required for long lifetime, high current capability, repetition rate, small breakdown voltage variance while working in a small sealed cavity. In order to simulate the electrode erosion process and acquire the performance of the two electrode switch resembling the ones in the practical application, a simple test platform had been designed and fabricated. A Dynamic 3-D Aspheric Profiler and a Confocal Laser Scanning Microscope (CLSM) were utilized to help analyze the erosion characteristics by providing quantitative descriptions of 1-D, 2-D, and 3-D profiles. The results demonstrate that the surface roughness of both electrodes rose with the increase of accumulated transfer charge. Specifically, the edge position has a larger value of surface roughness than the central position. Moreover, the surface of cathode seems rougher than that of anode in the same area. For example, the surface roughness of cathode was 7.752μm at edge position whereas that of anode was 5.573μm after 20000 shots. In sum, the erosion in cathode is more severe and the surface morphology is too complex to be described by simple models. Therefore, the research of the two electrode gas switch under such rigorous conditions can both investigate the new phenomena which are not concerned before and provide useful guidance to the applications. Thus, this research is essential in scientific research and industrial applications.
High repetition rate, fast current rise, pseudo-spark switch

G Mechtersheimer,R Kohler,R Meyer

DOI: https://doi.org/10.1088/0022-3735/19/6/015

1986-06-01

Abstract:A pseudo-spark switch triggered by a pulsed low-current gas discharge has been developed. It switches medium voltages and currents of typically less than 20 kV and 10 kA, respectively. The switch works at high repetition rates of up to 100 kHz and fast rates of current rise of up to 5*1011 A s-1. At positive charging voltage, the jitter may be much smaller than 1 ns. This pseudo-spark switch has been successfully tested by running a discharge-heated longitudinal copper vapour laser and a transverse Blumlein N2 laser, replacing a hydrogen thyratron and a high-pressure spark gap switch, respectively.
Erosion of Stainless Steel Electrodes in a High-Repetition-rate Gas Spark Switch

Le Feng,Sheng Liu,Qinhao Bu,Jianchang Peng,Qiaogen Zhang

DOI: https://doi.org/10.1088/1742-6596/2903/1/012004

2024-01-01

Journal of Physics Conference Series

Abstract:Abstract High-repetition-rate gas spark switches are widely used in the field of nanosecond pulses. A discharge experimental platform has been established to investigate the erosion process of the electrodes in a high-repetition-rate gas spark switch. The surface morphology of the electrodes after different numbers of discharges at a repetition rate of 100 Hz is observed using a confocal laser scanning microscope. The results show that three different morphologies are presented on the electrode surface. Compared with the anode, the cathode surface has a higher roughness. There are irregular protrusions in the central area of the cathode, and small dot-like protrusions in the central area of the anode. The erosion process of the electrode at a high repetition rate can be divided into two stages. In the first stage, the roughness of the electrode increases with the discharge number. In the second stage, the arithmetic mean deviation of the central area of the cathode is maintained at around 4 μm, and on the central area of the anode, it is maintained at around 1 μm. The maximum profile peak height of the electrode continues to increase with the discharge number. This research has significant implications for the design of long-life gas spark switches.
Electrode erosion of a high energy impulse spark gap switch

Xueling Yao,ZhengZhong Zeng,Jinliang Chen

DOI: https://doi.org/10.1088/1009-0630/7/6/021

2005-01-01

Abstract:Based on the principle of thermal conduction, three metal alloys (stainless steel, copper-tungsten and graphite 0) were chosen as the material of the high impulse current discharging switch. Experimental results indicate that the mass loss and surface erosion morphology of the electrode are related with the electrode material (conductivity sigma, melting point T-m, density rho and thermal capacity c) and the impulse transferred charge (or energy) per impulse for the same total impulse transferred charge. The experimental results indicate that the mass loss of stainless steel, copper-tungsten and graphite are 380.10 mu g/C, 118.10 mu g/C and 81.90 mu g/C respectively under the condition of a total impulse transferred charge of 52.5 C and a transferred charge per impulse of 10.5 C. Under the same impulse transferred charge, the mass loss of copper-tungsten (118.10 mu g/C) with the transferred charge per impulse at 10.5 C is far larger than the mass loss (38.61 mu g/C) at a 1.48 C transferred charge per impulse. The electrode erosion mechanism under high energy impulse arcs is analyzed briefly and it is suggested that by selecting high conductive metal or metal alloy as the electrode material of a high energy impulse spark gap switch and setting high erosion resistance material at the top of the electrode, the mass loss of the electrode can be reduced and the life of the switch prolonged.
Researches on Electrode Erosion of Gas Spark Switch under Pulsed Current

LIU Xuandong,SHEN Xi,LI Xiao'ang,FENG Lei,ZHANG Qiaogen

DOI: https://doi.org/10.13336/j.1003-6520.hve.20170831040

2017-01-01

Abstract:Gas spark switch is widely used in the field of pulsed power technology.As one of the key components,gas spark switch dramatically influences the output parameters and operation stabilities of large-scale pulsed power facilities.Electrode erosion is an inevitable problem,which is concerned and studied since the beginning of the application of gas spark switch from the year 1950 to 1960.In view of electrode erosion of gas spark switch,domestic and overseas researchers extensively studied the following aspects:morphology change of electrode surface,characterization parameters of etch pits,analysis of erosion heat sources,remove forces of electrode material,and effect of electrode erosion on performances of gas spark switch,etc.Several characterization parameters for etch pits on the surface of electrode,as well as classical 1D and 2D models for electrode erosion were proposed.Influences of electrode erosion on triggered performance of gas spark switch under repetitive operation were preliminarily studied.The main problems of the previous researches were analyzed.The probable differences of electrode erosion mechanism under repetitive fast front pulse from the previous researches were discussed.The direction and key techniques of further investigations on electrode erosion were pointed out finally.
A Miniaturized Sealed-Off Double-Gap Pseudospark Switch for High Power and High Repetition Rate Pulsed Discharge Applications

Weizong Wang,Jiaqi Yan,Guoxiang Sun,W. Ding,S. Shen

DOI: https://doi.org/10.1109/TIA.2023.3247401

IF: 4.079

2023-05-01

IEEE Transactions on Industry Applications

Abstract:Pulsed power systems can deliver high peak power in a micro/nano-second timescale to various loads in scientific and industrial applications, whose performances are significantly influenced by the pulsed discharge switch. This article presents the development and comprehensive tests of a miniaturized sealed-off pseudospark switch. The structure of double-gap and multi-channel is adopted to achieve the high hold-off voltage and high current capacity. In single pulse tests, the influence of pressure in the switch is analyzed. As the pressure increases, values of multiple parameters decrease, like self-breakdown voltage, trigger delay, and voltage dropping time. In a wide pressure range, trigger jitter is below 3 ns, and the minimum is <1 ns. At low pressure, the transient voltage across two gaps becomes inconsistent, and two types of current quenching are observed, which are related to processes occurring on cathode surface. In repetitive pulse tests, the direct repetitive operation is up to 3.5 kHz while higher repetition rate is limited by the trigger system. In double-pulse tests, the maximum repetition rate can be higher than 8 kHz for 40 kV pulsed voltage. Meanwhile, the insulation recovery speed is higher at lower pressure, and as the time delay between two pulses increases, the second pulse breakdown voltage increases nonlinearly. In high current tests, the switch is also used in metal wire explosion experiments and operates at the condition of 30 kV/40 kA for more than 104 shots without performance degradation. Further lifetime tests point out that the switch can work for >106 shots stably at moderate current. Experiments prove that the designed switch has superior performances including high hold-off voltage (>50 kV), low jitter (<1 ns), high repetition rate (>3.5 kHz), high peak current (>40 kA), long lifetime (>106 shots) and miniaturized size.

Physics,Engineering

Test of SiC-electrodes in a high current pseudospark switch

Electrode Phenomena and Measurements of the Erosion Rate in High-Current Pseudospark-Switches

Sealed-off Pseudospark Switches for Pulsed Power

Reliability Analysis for Commercial SiC MOSFETs in Single Pulse and Repetitive Surge Current Test

Scientific and Technological Progress of Pseudospark Devices

Interferometric measurement of the electron density in a pseudospark switch

Effect of Different Electrode Materials on Electrode Erosion Characteristics and Failure Modes of Gas Spark Switch

Long Lifetime, Triggered, Spark-Gap Switch For Repetitive Pulsed Power Applications

Characteristics of pseudospark switches for pulsed power modulators

Multiple-Gap Spark Gap Switch

Design and Performance Analysis of Multi-gap Multi-channel Spark Switch with LCR Triggered Method

The effect of intermediate electrode on pseudo-spark switch performance with high repetition rate

Influence of metal vapour release on pseudospark switch performance

Low-Pressure Pseudospark Switches for Icf Pulsed Power

Experimental Study of Electrode Erosion and Aging Process of a Specially Designed Gas Switch under Repetitive Arc Discharge

Surface Morphology of Cu-W Alloy Electrodes in a Long Lifetime Gas Spark Switch

High repetition rate, fast current rise, pseudo-spark switch

Erosion of Stainless Steel Electrodes in a High-Repetition-rate Gas Spark Switch

Electrode erosion of a high energy impulse spark gap switch

Researches on Electrode Erosion of Gas Spark Switch under Pulsed Current

A Miniaturized Sealed-Off Double-Gap Pseudospark Switch for High Power and High Repetition Rate Pulsed Discharge Applications