Abstract:Dislocation slips, twinning, shear banding (SBs), strain localization, and martensite formation are a few deformation modes that are activated in BCC metals and alloys. Strain, strain rate, and deformation temperature are other parameters that determine the activation of deformation modes in BCC alloys. This review focuses on several BCC alloys, such as beta-titanium (β-Ti), tantalum (Ta), and ferritic stainless steels (FSSs), all of which exhibit differences in deformation behavior. These alloys often undergo thermo-mechanical processing (TMP) to enhance their mechanical properties. TMP leads to the evolution of deformation-induced products, such as SBs, strain-induced martensite (SIM), strain localizations, and mechanical/deformation twins (DTs) during plastic deformation, while also influencing crystallographic texture. The deformation modes in β-Ti depend upon the stability of the β-phase (i.e., β-stabilizers); low-stability alloys show the formation of SIM along with slips and twins, whereas in highly stable β-Ti alloys, only slip+twin modes are observed as the primary deformation mechanisms. In the case of Ta, slip activity predominantly occurs on {110} planes, but it can also occur on planes with the highest resolved shear stress. The breakdown of Schmid's law or non-Schmid behavior for Ta and Ta-W alloys has been discussed in detail. The cold rolling (CR) of FSSs results in the formation of ridges, which is an undesirable phenomenon leading to very low formability. The microstructures of the rolled sheets consist of elongated ferrite grains with in-grain SBs, which are preferentially formed in the γ-fiber-oriented grains. The formation of finer grains after recrystallization improves both the mechanical properties and ridging resistance in FSS. Therefore, this review comprehensively reports on the impact of TMP on the microstructural and crystallographic texture evolution during the plastic deformation and annealing treatment of β-Ti, Ta alloys, and FSSs in BCC materials, using results obtained from electron microscopy and X-ray diffraction.

Microstructure and twinning behavior of b.c.c tantalum under dynamic plastic deformation

Discrete Twinning Dynamics and Size-Dependent Dislocation-to Twin Transition in Body-Centred Cubic Tungsten

Unstable Twin In Body-Centered Cubic Tungsten Nanocrystals

Bending-induced Deformation Twinning in Body-Centered Cubic Tungsten Nanowires

Study on deformation behavior of tantalum under cryogenic temperature dynamic plastic deformation

Deformation Mechanism of Metastable Oriented Grains in High-Purity Tantalum under Different Strain Paths

Microstructure evolution and the deformation mechanism in nanocrystalline superior-deformed tantalum

Influence of tantalum composition on mechanical behavior and deformation mechanisms of TiZrHfTax high entropy alloys

Plastic Deformation Behavior of a Cu–10Ta Alloy under Strong Impact Loading

In situ observation of dislocations at crack tip insingle crystalline tantalum

Atomic-scale observation of nucleation- and growth-controlled deformation twinning in body-centered cubic nanocrystals

Evolution of Microstructure and Crystallographic Texture in Deformed and Annealed BCC Metals and Alloys: A Review

Influence of grain boundary and twin boundary on the stretching deformation behaviors of Cu/Ta interface material

Microstructure and Texture Evolution of Ta32 Titanium Alloy During Superplastic Deformation

Unraveling the temperature-dependent plastic deformation mechanisms of polycrystalline Ta implants through numerical analysis of grain boundary dynamics

Twinning-induced plasticity (TWIP) effect in multi-phase metastable beta Zr-Nb alloys

Experimental Study for the Influence of Twinning on the Plastic Deformation of Pure Polycrystalline Titanium

Microstructure and Strength of a Tantalum-Tungsten Alloy after Cold Rolling from Small to Large Strains

Microstructural Evolution of Ta-4%W During Cold Rolling

Analysis of Stored Energy Distribution in Three Directions of Tantalum in Deformed and Annealed States

Multiscale Simulation Study on the Spallation Characteristics of Ductile Metal Ta under High Strain Rate Impact