Abstract:To bring the potential power of the capacitively coupled contactless conductivity detection ((CD)-D-4) technique to full play and extend the application fields of (CD)-D-4, our previous work has developed a (CD)-D-4 sensor which is suitable for conductivity detection of electrolyte solution in industrial fields (Sensors and Actuators A 213 (2014) 1-8). With the introduction of series resonance principle, the (CD)-D-4 sensor can overcome the influence of coupling capacitances on conductivity measurement. By a specific design of shield configuration, the (CD)-D-4 sensor can overcome the influence of stray capacitances and the environment interference in industrial fields. Although the measurement performance of the (CD)-D-4 sensor is satisfactory and it is suitable for the conductivity detection in industrial fields, the input-output characteristic of the (CD)-D-4 sensor is non-monotonic, which may limit the practical applications of the (CD)-D-4 sensor. To overcome this drawback, an improved (CD)-D-4 sensor for conductivity detection in industrial fields has been developed. The basic conductivity measurement method (the series resonance principle) and the shield configuration of the improved (CD)-D-4 sensor are the same as those of the (CD)-D-4 sensor in our previous work. However, the measurement circuit of the detection path of the improved (CD)-D-4 sensor has been optimized. The one-inductor design has been replaced by a two-inductor design. With this optimization, the input-output characteristic of the improved (CD)-D-4 sensor is theoretically monotonic. Conductivity measurement experiments were carried out on four pipes with inner diameters of 1.8 mm, 3.3 mm, 5.0 mm and 7.6 mm, respectively. The experimental results indicate that the development of the improved (CD)-D-4 sensor is successful. In comparison with the previous (CD)-D-4 sensor, the measurement accuracy of the improved (CD)-D-4 sensor is comparable. But, the improved (CD)-D-4 sensor has the advantages of the monotonic input-output characteristic and the convenience for practical conductivity detection in industrial fields. Meanwhile, it is found that the input-output characteristic of the improved (CD)-D-4 sensor is nonlinear and the sensitivity of the improved (CD)-D-4 sensor decreases with the increase of conductivity. (C) 2015 Elsevier B.V. All rights reserved.

Simulation and optimization of conductor structural parameters of free-space hall-effect current sensor

An Improved Capacitively Coupled Contactless Conductivity Detection Sensor for Industrial Applications

Study on the Application of Simulated Inductor Technique to the Design of C 4 D Sensor

New C4D Sensor with a Simulated Inductor

Optimization of integrated hall sensor

Design and Implementation of an Industrial C4D Sensor for Conductivity Detection

Online Measurement of Conductivity/permittivity of Fluid by a New Contactless Impedance Sensor.

An Analytical Geometry Optimization Model for Current-Mode Cross-Like Hall Plates

Inspection of defects in conductive multi-layered structures by an eddy current scanning technique: Simulation and experiments

A New Design of a Single-Device 3D Hall Sensor: Cross-Shaped 3D Hall Sensor

Linearity Range Extension of Magnetostrictive Current Sensors Through Magnetic Circuit Optimization

Design of Heart-Shaped Current Sensor Based on Incomplete Magnetic Cancellation

Study of Current Measurement Method Based on Circular Magnetic Field Sensing Array

Influences of an Aluminum Covering Layer on the Performance of Cross-Like Hall Devices

A 3-D GaAs-based Hall Sensor Design With Dual Active Layers Structure

Forward Model and Simulator of Thickness Measurement of Multi-Layered Conductive Structures by Eddy Current Technique

A CMOS Front-End Hall Sensor Microsystem for Linear Magnetic Field Measurement With Best Tradeoff Between Sensitivity and SNR

Optimal Design of Differential Sensor Array for Interference Elimination of Noninvasive Multicore Cable Current Measurement

Analytical Model for Eddy Current Testing of Thickness of Multi-layered Structures and Experimental Verification

Non-contact surface water conductivity measurement system

Modeling of Three-Axis Hall Effect Sensor Based on CMOS Process