Active Surface Plasmon Sensor

Ren-Min Ma,Sadao Ota,Yimin Li,Sui Yang,Xiang Zhang

DOI: https://doi.org/10.1364/cleo_qels.2014.fm3k.7

2014-01-01

Abstract:we have experimentally demonstrated an active plasmon sensor with sub-p.p.b. level explosive molecules detection. Loss compensation by gain in surface plasmon cavity enhanced the sensitivity significantly.

What problem does this paper attempt to address?

Plasmonic Laser Sensors (presentation Recording)

Renmin Ma,Sadao Ota,Yimin Li,Sui Yang,Xiang Zhang

DOI: https://doi.org/10.1117/12.2186086

2015-01-01

Abstract:Perhaps the most successful application of plasmonics to date has been in sensing, where the interaction of a nanoscale localized field with analytes leads to high-sensitivity detection in real time and in a label-free fashion. However, all previous designs have been based on passively excited surface plasmons, in which sensitivity is intrinsically limited by the low quality factors induced by metal losses. It has recently been proposed theoretically that surface plasmon sensors with active excitation (gain-enhanced) can achieve much higher sensitivities due to the amplification of the surface plasmons. Here, we experimentally demonstrate an active plasmon sensor that is free of metal losses and operating deep below the diffraction limit for visible light. Loss compensation leads to an intense and sharp lasing emission that is ultrasensitive to adsorbed molecules. We validated the efficacy of our sensor to detect explosives in air under normal conditions and have achieved a sub-part-per-billion detection limit, the lowest reported to date for plasmonic sensors with 2,4-dinitrotoluene and ammonium nitrate. The selectivity between 2,4-dinitrotoluene, ammoniumnitrate and nitrobenzene is on a par with other state-of-the-art explosives detectors. Our results show that monitoring the change of the lasing intensity is a superior method than monitoring the wavelength shift, as is widely used in passive surface plasmon sensors. We therefore envisage that nanoscopic sensors that make use of plasmonic lasing could become an important tool in security screening and biomolecular diagnostics.
A Symmetrical Optical Waveguide Based Surface Plasmon Resonance Biosensing System

Heng Shi,Zhiyi Liu,Xiaoxiao Wang,Jun Guo,Le Liu,Lin Luo,Jihua Guo,Hui Ma,Shuqing Sun,Yonghong He

DOI: https://doi.org/10.1016/j.snb.2013.05.005

2013-01-01

Abstract:In this work, we propose a MgF2/Au/MgF2/Analyte based, angle-interrogation surface plasmon resonance sensor. This symmetrical structure results in higher surface electric field strengths, and longer surface propagation lengths and depths. A refractive index resolution of 8.1×10−8RIU in fluid protocol and 3.5×10−7RIU in atmosphere protocol is acquired by a simple SPR imaging system. In order to demonstrate the biomedical applications of this system, we detect Escherichia coli with different concentrations using dopamine film on the sensor surface to immobilize antibodies. A detection limit of 103cfu/mL of E. coli bacteria is acquired from this system.
Nanoplasmonic Biosensor Using Localized Surface Plasmon Resonance Spectroscopy for Biochemical Detection.

Diming Zhang,Qian Zhang,Yanli Lu,Yao,Shuang Li,Qingjun Liu

DOI: https://doi.org/10.1007/978-1-4939-6848-0_6

2017-01-01

Abstract:Localized surface plasmon resonance (LSPR) associated with metal nanostructures has developed into a highly useful sensor technique. Optical LSPR spectroscopy of nanostructures often shows sharp absorption and scattering peaks, which can be used to probe several bio-molecular interactions. Here, we report nanoplasmonic biosensors using LSPR on nanocup arrays (nanoCA) to recognize bio-molecular binding for biochemical detection. These sensors can be modified to quantify binding of small molecules to proteins for odorant and explosive detections. Electrochemical LSPR biosensors can also be designed by coupling electrochemistry and LSPR spectroscopy measurements. Multiple sensing information can be obtained and electrochemical LSPR property can be investigated for biosensors. In some applications, the electrochemical LSPR biosensor can be used to quantify immunoreactions and enzymatic activity. The biosensors exhibit better performance than those of conventional optical LSPR measurements. With multi-transducers, the nanoplasmonic biosensor can provide a promising approach for bio-detection in environmental monitoring, healthcare diagnostics, and food quality control.
Plasmonic Nano-Arrays for Ultrasensitive Bio-Sensing

Jing Jiang,Xinhao Wang,Shuang Li,Fei Ding,Nantao Li,Shaoyu Meng,Ruifan Li,Jia Qi,Qingjun Liu,Gang Logan Liu

DOI: https://doi.org/10.1515/nanoph-2018-0023

IF: 7.5

2018-01-01

Nanophotonics

Abstract:Surface plasmon resonance (SPR) and localized SPR (LSPR) effects have been shown as the principles of some highlysensitive sensors in recent decades. Due to the advances in nano-fabrication technology, the plasmon nano-array sensors based on SPR and LSPR phenomena have been widely used in chemical and bioloical analysis. Sensing with surface-enhanced field and sensing for refractive index changes are able to identify the analytes quantitatively and qualitatively. With the newly developed ultrasensitive plasmonic biosensors, platforms with excellent performance have been built for various biomedical applications, including point-of-care diagnosis and personalized medicine. In addition, flexible integration of plasmonics nano-arrays and combining them with electrochemical sensing have significantly enlarged the application scenarios of the plasmonic nano-array sensors, as well as improved the sensing accuracy.
Plasmon Lasers for Sensing

Renmin Ma

DOI: https://doi.org/10.1109/piers.2016.7734215

2016-01-01

Abstract:The resonance phenomena of surface plasmons have led to a novel class of non-contact, real-time and label-free optical sensors which have become a central tool in biochemical sensing and detection. However, all kinds of surface plasmon resonances are with natively strong non-radiative Drude damping that weakens the resonance and limits the sensing performance fundamentally. We demonstrated that these dampings can be fully compensated by gain medium at a plasmon lasing state which can lead to a new class of plasmon laser sensors.
Design of a Surface Plasmon Resonance Sensor Based on Grating Connection

Jun Zhu,Liuli Qin,Shuxiang Song,Junwen Zhong,Siyuan Lin

DOI: https://doi.org/10.1007/s13320-015-0244-1

2015-01-01

Abstract:Nowdays, the study of measurement of the biological field focuses on the research of improving surface plasmon resonance (SPR) in the fields of integration and detection sensitivity. We designed a kind of grating connected surface plasmon resonance sensor. Theoretically, we analyzed the wave vector and the effective refractive index relations with the diffraction grating structure. Then we obtained the nanoparticles enhancement SPR structure with a resolution 10 times higher than that of traditional SPR sensors. Also, we used the finite-difference time-domain (FDTD) analysis and simulation which showed that it was obvious with coupling effect by the nanoparticles enhancement SPR structure that the reflectance spectral bandwidth results validated the structure significantly which improved the sensitivity. Experimental results showed that the dynamic response of the designed sensor reached 10 −6 RIU (refractive index unit). This study has the certain significance to long-distance and special sensing applications.
Intensity-Modulated Surface Plasmon Resonance Array Sensor Based on Polarization Control

Boshu Sun,Xiaoping Wang,Zihao Huang

DOI: https://doi.org/10.1109/bmei.2010.5639280

2010-01-01

Abstract:Intensity-modulated surface plasmon resonance (SPR) array sensor based on polarization control was introduced and the impacts of incident angle, gold firm thickness, polarizer angle, wavelength and data processing on its sensitivity and measuring range were analyzed. It was concluded that in an easily controllable measurement range, an appropriate parameter selection can be set and produce high sensitivity with a simple optical and mechanical structure and lower production costs. This scheme can be widely applied to the high-throughput detection of bimolecular interaction analysis, environment monitoring, food safety, pharmaceutical analysis, biomedical engineering and other fields.
Hybrid Structure–Based SPR Sensor for Chemical Sensing with Enhanced Sensitivity

Mohan Kumar Paswan,Rikmantra Basu

DOI: https://doi.org/10.1007/s11468-023-02020-7

IF: 2.726

2023-09-07

Plasmonics

Abstract:In this paper, we have proposed a new multilayer structure and investigated its performance as a chemical sensor utilizing surface plasmon resonance. Our proposed design consists of a black phosphorus layer sandwiched between a metal layer and a graphene layer, blue phosphorene/MoS 2 heterostructure layers placed over it, and the sensing layer containing the analyte placed on top. A CaF 2 prism in the Kretschmann configuration is employed to excite surface plasmon resonance (SPR), and the angle interrogation method is used for analysis. Sellmeier equations calculate the reflectivity and other parameters of the multilayer design. We also study the effect of the combination of BP and metal interlayer. Analysis of the proposed design shows significantly improved sensitivity compared to recent SPR-based sensors. In this paper, the sensitivity of 466°/RIU is obtained with silver metal, BP, graphene, and BlueP/MoS 2 layers SPR sensor.

materials science, multidisciplinary,nanoscience & nanotechnology,chemistry, physical
Study and Numerical Simulation of a Surface Plasmon Resonance Sensor Using Bi-Beam Differential Measurement Approach

ZHANG Xue-jiao,WANG Xiao-ping

DOI: https://doi.org/10.3969/j.issn.1003-501x.2007.07.014

2007-01-01

Abstract:In this article, a novel measurement approach of Surface Plasmon Resonance (SPR) with bi-beam was presented in order to improve the sensitivity and anti-disturbance capability of intensity-modulated SPR sensor. The relation curves between reflected light intensity and sample refractive index were established at different incident angles and gold film thickness, based on theoretical calculation and numerical simulation of this new method. Compared with the traditional intensity-modulated technology, studies indicates that bi-beam approach has better sensitivity and broader measuring range when the incident angle difference of the two beams is equal to 5 degree and gold film thickness is in the range of 40 to 50 nm. The noiseproof feature and stability of the sensor system are greatly improved with the application of light intensity difference technology.
Explosives Detection in a Lasing Plasmon Nanocavity.

Ren-Min Ma,Sadao Ota,Yimin Li,Sui Yang,Xiang Zhang

DOI: https://doi.org/10.1038/nnano.2014.135

IF: 38.3

2014-01-01

Nature Nanotechnology

Abstract:gain-enhanced plasmon laser is used to detect explosives with sub-ppb detection limit.
Fabry-Perot Type Sensor With Surface Plasmon Resonance

Guowei Lü,BoLin Cheng,Hong Shen,Yueliang Zhou,Zhenghao Chen,Guozhen Yang,Olivier Tillement,Stéphane P. Roux,Pascal Perriat

DOI: https://doi.org/10.1063/1.2398885

IF: 4

2006-01-01

Applied Physics Letters

Abstract:The main point of this letter concerns the fabrication of an optical sensor with improved sensitivity for detecting molecular adsorption onto a gold surface. The sensor consists of a Fabry-Perot interferometer whose one of two reflective layers is constituted by an island-type gold film having a pronounced local surface plasmon resonance. The results presented in the letter show that the binding of molecules on the device surface induces a differential interference pattern whose amplitude is increased by the plasmon resonance. The sensor sensitivity can be improved by further deposition of Au nanoparticles on the reflective layer. This kind of sensor has potential advantages since it is easy to fabricate and use and it possesses a submonolayer sensitivity.
Surface Plasmonic Sensors: Sensing Mechanism and Recent Applications

Qilin Duan,Yineng Liu,Shanshan Chang,Huanyang Chen,Jin-hui Chen

DOI: https://doi.org/10.3390/s21165262

IF: 3.9

2021-08-04

Sensors

Abstract:Surface plasmonic sensors have been widely used in biology, chemistry, and environment monitoring. These sensors exhibit extraordinary sensitivity based on surface plasmon resonance (SPR) or localized surface plasmon resonance (LSPR) effects, and they have found commercial applications. In this review, we present recent progress in the field of surface plasmonic sensors, mainly in the configurations of planar metastructures and optical-fiber waveguides. In the metastructure platform, the optical sensors based on LSPR, hyperbolic dispersion, Fano resonance, and two-dimensional (2D) materials integration are introduced. The optical-fiber sensors integrated with LSPR/SPR structures and 2D materials are summarized. We also introduce the recent advances in quantum plasmonic sensing beyond the classical shot noise limit. The challenges and opportunities in this field are discussed.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Lasing Enhanced Surface Plasmon Resonance Sensing

Xing-Yuan Wang,Yi-Lun Wang,Suo Wang,Bo Li,Xiao-Wei Zhang,Lun Dai,Ren-Min Ma

DOI: https://doi.org/10.1515/nanoph-2016-0006

IF: 7.5

2017-01-01

Nanophotonics

Abstract:The resonance phenomena of surface plasmons has enabled development of a novel class of noncontact, real-time and label-free optical sensors, which have emerged as a prominent tool in biochemical sensing and detection. However, various forms of surface plasmon resonances occur with natively strong non-radiative Drude damping that weakens the resonance and limits the sensing performance fundamentally. Here we experimentally demonstrate the first lasing-enhanced surface plasmon resonance (LESPR) refractive index sensor. The figure of merit (FOM) of intensity sensing is ~84,000, which is about 400 times higher than state-of-the-art surface plasmon resonance (SPR) sensor. We found that the high FOM originates from three unique features of LESPR sensors: high-quality factor, nearly zero background emission and the Gaussian-shaped lasing spectra. The LESPR sensors may form the basis for a novel class of plasmonic sensors with unprecedented performance for a broad range of applications.
Wavelength-multiplexing Phase-Sensitive Surface Plasmon Imaging Sensor

Yonghong Shao,Yan Li,Dayong Gu,Kai Zhang,Junle Qu,Jianan He,Xuejin Li,Shu-Yuen Wu,Ho-Pui Ho,Michael G. Somekh,Hanben Niu

DOI: https://doi.org/10.1364/ol.38.001370

2013-01-01

Abstract:A wavelength-multiplexing phase-sensitive surface plasmon resonance (SPR) imaging sensor offering wide dynamic detection range and microarray capability is reported. Phase detection is accomplished by performing self-interference between the s- and p- polarizations within the signal beam. A liquid crystal tunable filter is used to sequentially select the SPR excitation wavelength from a white light source. This wavelength-multiplexing approach enables fast detection of the sensor's SPR phase response over a wide range of wavelengths, thereby covering literally any regions of interest within the SPR dip and thus maintaining the highest sensitivity point at all times. The phase-sensitive approach is particularly important for imaging SPR sensing applications because of its less stringent requirements for intensity signal-to-noise ratio, which also means the possibility of using uncooled modest resolution analog-to-digital conversion imaging devices. Experimental results demonstrate a resolution of 2.7×10(-7) RIU with a dynamic range of 0.0138 RIU.
Localized surface plasmon resonance biosensor: an improved technique for SERS response intensification.

A. Dinovitser,B. Ng,M. S. Islam,J. Sultana,Rifat Ahmmed Aoni,D. Abbott,M. S. Habib

DOI: https://doi.org/10.1364/OL.44.001134

IF: 3.6

2019-02-21

Optics Letters

Abstract:As technology continues to advance, the development of novel sensing systems opens new possibilities for low-cost, practical biosensing applications. In this Letter, we demonstrate a localized surface plasmon resonance system that combines both wave-guiding and plasmonic resonance sensing with a single microstructured polymeric structure. Characterizing the sensor using the finite element method simulation shows, to the best of our knowledge, a record wavelength sensitivity (WS) of 111000 nm/refractive index unit (RIU), high amplitude sensitivity (AS) of 2050 RIU-1, high sensor resolution and limit of detection of 9×10-7 RIU and 8.12×10-12 RIU2/nm, respectively. Furthermore, these sensors have the capability to detect an analyte within the refractive index range of 1.33-1.43 in the visible to mid-IR, therefore being potentially suitable for applications in biomolecular and chemical analyte detection.

Chemistry,Medicine,Engineering,Materials Science
Flexible Surface-Enhanced Raman Scattering Chip: A Universal Platform for Real-Time Interfacial Molecular Analysis with Femtomolar Sensitivity

Qi Hao,Mingze Li,Jiawei Wang,Xingce Fan,Jie Jiang,Xiaoxia Wang,Minshen Zhu,Teng Qiu,Libo Ma,Paul K. Chu,Oliver G. Schmidt

DOI: https://doi.org/10.1021/acsami.0c16315

2020-11-18

Abstract:We propose and demonstrate a flexible surface-enhanced Raman scattering (SERS) chip as a versatile platform for femtomolar detection and real-time interfacial molecule analysis. The flexible SERS chip is composed of a flexible and transparent membrane and embedded plasmonic dimers with ultrahigh particle density and ultrasmall dimer gap. The chip enables rapid identification for residuals on solid substrates with irregular surfaces or dissolved analytes in aqueous solution. The sensitivity for liquid-state measurement is down to 0.06 molecule per dimers for 10–14 mol·L–1 Rhodamine 6G molecule without molecule enrichment. Strong signal fluctuation and blinking are observed at this concentration, indicating that the detection limit is close to the single-molecule level. Meanwhile, the homogeneous liquid environment facilities accurate SERS quantification of analytes with a wide dynamic range. The synergy of flexibility and liquid-state measurement opens up avenues for the real-time study of chemical reactions. The reduction from p-nitrothiophenol (PNTP) to p-aminothiophenol (PATP) in the absence of the chemical reducing agents is observed at liquid interfaces by in situ SERS measurements, and the plasmon-induced hot electron is demonstrated to drive the catalytic reaction. We believe this robust and feasible approach is promising in extending the SERS technique as a general method for identifying interfacial molecular traces, tracking the evolution of heterogeneous reactions, elucidating the reaction mechanisms, and evaluating the environmental effects such as pH value and salty ions in SERS.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c16315?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c16315</a>.Method of fabricating plasmonic nanoarrays using ultrathin anodic aluminum oxide (AAO) membranes; proof-of-concept experiment demonstrating the good adhesion between the flexible SERS chip and the substrates; relative standard deviation (RSD) of Raman signals in liquid-state SERS measurements; dispersion of Raman intensity in solid-state measurement; and additional analysis data about the real-time in situ observation of Raman spectra in plasmon-induced photocatalytic reduction (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c16315/suppl_file/am0c16315_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,nanoscience & nanotechnology
Recent Advances in Plasmonic Sensors

Lianming Tong,Hong Wei,Shunping Zhang,Hongxing Xu

DOI: https://doi.org/10.3390/s140507959

2014-01-01

Abstract:Plasmonic sensing has been an important multidisciplinary research field and has been extensively used in detection of trace molecules in chemistry and biology. The sensing techniques are typically based on surface-enhanced spectroscopies and surface plasmon resonances (SPRs). This review article deals with some recent advances in surface-enhanced Raman scattering (SERS) sensors and SPR sensors using either localized surface plasmon resonances (LSPRs) or propagating surface plasmon polaritons (SPPs). The advances discussed herein present some improvements in SERS and SPR sensing, as well as a new type of nanowire-based SPP sensor.
Lasing-enhanced Surface Plasmon Resonance Spectroscopy and Sensing

Zhe Zhang,Leona Nest,Suo Wang,Si-Yi Wang,Ren-Min Ma

DOI: https://doi.org/10.1364/prj.431612

IF: 7.6

2021-01-01

Photonics Research

Abstract:Surface plasmon resonance (SPR) sensors are a prominent means to detect biological and chemical analytes and to investigate biomolecular interactions in various fields. However, the performance of SPR sensors is ultimately limited by ohmic loss, which substantially weakens the resonance signal and broadens the response linewidth. Recent studies have shown that ohmic loss can be fully compensated in plasmonic nanolasers, which leads to a novel class of lasing-enhanced surface plasmon resonance (LESPR) sensors with improved sensing performance. In this paper, we detail the underlying physical mechanisms of LESPR sensors and present their implementation in various sensing devices. We review recent progress on their applications, particularly for refractive index sensing, gas detection and biological imaging, labeling, tracking, and diagnosis. We then summarize the review and highlight remaining challenges of LESPR sensing technology.
Compact hybrid plasmonic slot waveguide sensor with a giant enhancement factor for surface-enhanced Raman scattering application

Suoming Wang,Yanying Zhu,Sijie Luo,Erkuang Zhu,Shuqing Chen

DOI: https://doi.org/10.1364/OE.431274

2021-08-02

Abstract:In this paper, a surface-enhanced Raman scattering (SERS) sensor with a giant field enhancement factor based on the coupling of surface plasmon polaritons (SPPs) is designed and studied theoretically. The proposed sensor adopts a metal-dielectric layered hybrid slot waveguide structure, combining thin metal (gold) layers and silicon nitride strip waveguides. Unlike other similar sensors, the silicon nitride waveguide structure does not serve as an excitation signal channel, conventionally loaded with the guided modes, but as an auxiliary layer, making it easier to concentrate the light field in the slot. Therefore, the sensor has a higher enhancement factor compared to the pure metal or dielectric slot structure. The results exhibit that we can obtain a maximum enhancement factor exceeding 10^6 under the compact configuration of 510 × 300 × 225nm^3 at the wavelength of 785 nm. By analyzing the dependence of the sensor performance on the structural parameters, we show that the structure of such sensor can directly be applied to SERS spectroscopic analysis as well as integrated with micro-and nano-photonic platform to perform on-chip detection system.
Research advances on surface plasmon resonance biosensors

Qi Wang,Zi-Han Ren,Wan-Ming Zhao,Lei Wang,Xin Yan,Ai-Song Zhu,Feng-Mei Qiu,Ke-Ke Zhang,Ai-song Zhu,Feng-mei Qiu

DOI: https://doi.org/10.1039/d1nr05400g

IF: 6.7

2022-01-01

Nanoscale

Abstract:The surface plasmon resonance (SPR) phenomenon is of wide interest due to its sensitivity to changes in surface refractive index for the label-free, highly sensitive and rapid detection of biomarkers.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry

Active Surface Plasmon Sensor

Plasmonic Laser Sensors (presentation Recording)

A Symmetrical Optical Waveguide Based Surface Plasmon Resonance Biosensing System

Nanoplasmonic Biosensor Using Localized Surface Plasmon Resonance Spectroscopy for Biochemical Detection.

Plasmonic Nano-Arrays for Ultrasensitive Bio-Sensing

Plasmon Lasers for Sensing

Design of a Surface Plasmon Resonance Sensor Based on Grating Connection

Intensity-Modulated Surface Plasmon Resonance Array Sensor Based on Polarization Control

Hybrid Structure–Based SPR Sensor for Chemical Sensing with Enhanced Sensitivity

Study and Numerical Simulation of a Surface Plasmon Resonance Sensor Using Bi-Beam Differential Measurement Approach

Explosives Detection in a Lasing Plasmon Nanocavity.

Fabry-Perot Type Sensor With Surface Plasmon Resonance

Surface Plasmonic Sensors: Sensing Mechanism and Recent Applications

Lasing Enhanced Surface Plasmon Resonance Sensing

Wavelength-multiplexing Phase-Sensitive Surface Plasmon Imaging Sensor

Localized surface plasmon resonance biosensor: an improved technique for SERS response intensification.

Flexible Surface-Enhanced Raman Scattering Chip: A Universal Platform for Real-Time Interfacial Molecular Analysis with Femtomolar Sensitivity

Recent Advances in Plasmonic Sensors

Lasing-enhanced Surface Plasmon Resonance Spectroscopy and Sensing

Compact hybrid plasmonic slot waveguide sensor with a giant enhancement factor for surface-enhanced Raman scattering application

Research advances on surface plasmon resonance biosensors