Abstract:Abstract The survivability and reliability of commercial electronic components under very high thermo-mechanical loads are improved using underfilling and potting methods. Potting protects from operating conditions such as moisture, water, or corrosive agents. Furthermore, potting offers damping against shock and vibrations, heat dissipation, and structural support. Being one of the most cost-efficient methods, potting greatly increases reliability and therefore reduces costs for replacements and repairs. It also addresses trapped hot air issues better than other restraint technologies. In potted electronic assemblies, interfacial delamination at the epoxy and PCB interface has been one of the major failure modes. Interfacial delamination happens at the epoxy/PCB interface under dynamic shock loads, which leads to failures at the solder interconnects of the electronic components. Sustained operation and storage at elevated temperatures change the interfacial characteristics at the epoxy/PCB interface. This research is focused on interfacial failure mechanics at epoxy/PCB interfaces with high-temperature isothermal aging. In the selection of epoxy potting material and the reliability assessments of the supplemental restraint systems, fracture parameters such as steady-state strain energy release rate stress and fracture toughness are critical. Rectangular beam specimens of the epoxy/PCB interface are fabricated for different potting compounds and the fracture behavior is studied under quasi-static monotonic three-point and four-point bend loads. One of the main differences between three-point and four-point bend loading is that the maximum bending stress occurs at the midpoint under the point of loading of the specimen in three-point bending, whereas the peak stress is distributed over the section of the specimen between the loading points in four-point bending. Four different potting compounds with diverse properties have been studied. The recommended curing schedule from the manufacturer has been chosen and followed for all the potting compounds. The epoxy/PCB interfacial samples are aged at a high temperature of 100°C for 30 to 180 days. Damage has been assumed to happen at the epoxy/PCB interface under dynamic loads. The critical load of crack initiation for the epoxy/PCB interface has been determined from the experimental findings, and it is used in the computation of fracture toughness values. The fracture toughness values are compared for the various epoxy/PCB systems based on the number of days of thermal aging and the method of flexure testing. A cohesive zone model has been constructed for predominantly mode-I delamination with four-point bend stress to predict the interfacial delamination behavior at the epoxy/PCB interfaces. It has been assumed that the bulk material is linear elastic during the bending load. The cohesive zone has been modeled at the interface, where the interfacial fracture has been assumed to occur. The fracture behavior in the simulation is predicted based on the fracture parameters determined through the experiment. The computed cohesive zone parameters are unique to the interfaces, they can be used across various applications with the same epoxy/PCB interface to predict interfacial delamination and to select a more suitable potting material.

Study on Encapsulation Reliability

Adhesion improvement of Cu-based substrate and epoxy molding compound interface by hierarchical structure preparation

Computational Analysis of Mechanical and Electromigration Reliability Problems

Study on the Delamination Between Adhesive Film and Silicon in Stacked-Die Packaging

Interfacial Delamination Characterization and Thermo-mechanical Reliability of Stacked Die Package by Finite Element Analysis

Study on the adhesion and reliability of Epoxy Molding Compound and shaped Pd Preplated leadframes

Study on the Hygrothermal Reliability of Underfill/Passivation Layer Interface Using the Silane Coupling Agent as Adhesion Promoter

Epoxy-PCB Interfacial Fracture Reliability under Three-Point and Four-Point Bend Loading After Sustained Elevated Temperature Exposure

Study The Mixed-Mode Delamination Of The Epoxy/Cu Interface

Delamination of Plasticized Devices in Dynamic Service Environments

An Extensive Simulation Study of the Interfacial Delamination in Molded Underfill Flip-Chip Packages by Finite Element Method Based on Virtual Crack Closure Technique

Study on the Interface Mechanism of Copper Migration Failure in Solder Mask-Substrate Package

A reliability study of adhesion mechanism between liquid crystal polymer and silicone adhesive

Finite element analysis of 2.5D packaging processes based on multi-physics field coupling for predicting the reliability of IC components

A Combined Simulation and Experimental Study on Cracking and Delamination Behavior at the Cu/Polyimide Interface of RDLs in Chiplet Package Subjected to Thermo-Mechanical Loads

Molding Void Issue And Solution Of A Package-In-Package

Enhancing Semiconductor Package Reliability through Mechanical Property Optimization of Pressureless Sintering Die Attach Adhesives

Researches on System Quality Control of Materials and Components for High Density Packaging

Discussion on influence of moisture absorption on the reliability of integrated circuit package

Reliability Analysis and Evaluation of Epoxy Resin Adhesive for LED Encapsulation

Moisture Assist Delamination In Multiple Die Stacked Package