Abstract:The Zr-ZrC-ZrC/DLC gradient composite films were prepared on TiNi alloy by the techniques combined plasma immersion ion implantation and deposition (PIIID) and plasma enhanced chemical vapor deposition (PECVD). With this method, the Zr-ZrC intermixed layers can be obtained by the ion implantation and deposition before the deposition of the ZrC/DLC composite film. In our study, an optimal gradient composite film has been deposited on the NiTi alloys by optimizing the process parameters for implantation and deposition. The surface topography was observed through AFM and the influence of the deposition voltage on the surface topography of the film was investigated. XPS results indicate that on the outmost layer, the Zr ions are mixed with the DLC film and form ZrC phase, the binding energy of C Is and the composition concentration of ZrC depend heavily on the bias voltage. With the increase of bias voltage, the content of ZrC and the ratio Of sp(3)/sp(2) firstly increases, reaching a maximum value at 200 V, and then decreases. The nano-indentation and friction experiments indicate that the gradient composite film at 200 V has a higher hardness and lower friction coefficient compared with that of the bare NiTi alloy. The microscratch curve tests indicate that gradient composite films have an excellent bonding property comparing to undoped DLC film. Based on the electrochemical measurement and ion releasing tests, we have found that the gradient composite films exhibit better corrosion resistance property and higher depression ability for the Ni ion releasing from the NiTi substrate in the Hank's solution at 37 degrees C. (C) 2007 Elsevier B.V. All rights reserved.

Characteristics of DLC containing Ti and Zr films deposited by reactive magnetron sputtering

The Effects of Ti/Ni Doping on the Friction and Wear Properties of DLC Coatings

Surface characteristics and corrosion behavior of DLC film on NiTi alloys

Improving the internal stress and wear resistance of DLC film by low content Ti doping

Effect of the DLC coating on the surface properties of the NiTi alloys

Effect of C2h2 Flow Rate on the Deposition of Zr-Zrc-Zrc/Dlc Gradient Nano-Composite Film on Biomedical Niti Alloy

Properties of Zr–ZrC–ZrC/DLC Gradient Films on TiNi Alloy by the PIIID Technique Combined with PECVD

Diamond-Like Carbon Thin Films Deposited On Ti6al4v Alloy Surface By Plasma Gun At Atmospheric Pressure

DLC films fabricated by plasma immersion ion implantation and deposition on the NiTi alloys for improving their corrosion resistance and biocompatibility

Characterisation of Ultra-Thin DLC Coatings by SEM/EDX, AFM and Electrochemical Techniques

Microstructure and Mechanical Properties of Dlc Films Doped with High Crystallinity Crn Nanoparticles

Mechanical and Tribological Properties of Ti-DLC Films with Different Ti Content by Magnetron Sputtering Technique

Preparation and Tribological Properties of DLC/Ti Film by Pulsed Laser Arc Deposition

EFFECT OF C2H2 FLOW RATE ON THE DEPOSITION OF TI-TIC-TIC/DLC GRADIENT NANO-COMPOSITE FILM ON NITI ALLOY

Influence of Target Current on the Structure of Ti-Doped DLC Films

Deposition of DLC coating on biomedical TiNi alloys by plasma based ion implantation to improve surface properties

Tribological Behaviors of W-Doped DLC Films

Surface modification of NiTi alloys using diamond-like carbon (DLC) fabricated by plasma immersion ion implantation and deposition (PIIID)

The corrosion behavior and hemocompatibility of TiNi alloys coated with DLC by plasma based ion implantation

Structure and mechanical properties of Ti alloyed DLC films

Ti-TiC-TiC/DLC gradient nano-composite film on a biomedical NiTi alloy.