Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Performance Improvement of Polymer Solar Cells by Using A Solvent-Treated Poly(3,4-Ethylenedioxythiophene):Poly(Styrenesulfonate) Buffer Layer

Low Boiling-point Solvents Treatment of PEDOT∶PSS Film for Optimized Photovoltaic Cell Performance

Simultaneously Enhancing the Efficiency and Stability of Perovskite Solar Cells by Using P3HT/PEDOT:PSS as a Double Hole Transport Layer

The effect of alcohol solvent treatment on the performance of inverted polymer solar cells

[6,6]-Phenyl-C61-butyric acid dimethylamino ester as a cathode buffer layer for high-performance polymer solar cells

PEDOT:PSS‐Free Polymer Non‐Fullerene Polymer Solar Cells with Efficiency up to 18.60% Employing a Binary‐Solvent‐Chlorinated ITO Anode

Highly Efficient Solar Cells Based on the Copolymer of Benzodithiophene and Thienopyrroledione with Solvent Annealing

Performance improvement of polymer solar cells with binary additives induced morphology optimization and interface modification simultaneously

Nonhalogenated‐Solvent‐Processed High‐Performance All‐Polymer Solar Cell with Efficiency over 14%

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

An Improved Performance of All Polymer Solar Cells enabled by Sequential Processing via Non-halogenated Solvents

Optimization of Ag/PCBM interface via solvent treatment for efficient perovskite solar cell

Understanding the Mechanism of PEDOT: PSS Modification Via Solvent on the Morphology of Perovskite Films for Efficient Solar Cells

Design and Optimization of High Performance P3HT: PCBM Polymer Solar Cell Using P3HT Buffer Layer

Improving the Conductivity of PEDOT:PSS Hole Transport Layer in Polymer Solar Cells Via Copper(II) Bromide Salt Doping

All‐polymer solar cells with over 16% efficiency and enhanced stability enabled by compatible solvent and polymer additives

Energy Level Tuning in CsPbBr3 Perovskite Solar Cells through In Situ-Polymerized PEDOT Hole Transport Layer

Layer‐by‐Layer All‐Polymer Solar Cells Approaching 19% with Dual‐Donor Modulation of an Interpenetrating Network

High Efficiency Layer‐by‐Layer All‐Polymer Solar Cell Enabled by Bottom‐Layer Optimization

Boosting the Efficiency of Non-fullerene Organic Solar Cells via a Simple Cathode Modification Method

High performance all-polymer solar cells enabled with solvent and solid dual additives