Abstract:In order to better understand the fracture mechanism of body-centered-cubic (BCC) metal, the multiscale quasi-continuum method (QC) is employed to analyze the nano-sized mode I cracks of three kinds of BCC metal materials, i.e., Ta, Fe and W. The plastic deformation near the crack tip and the brittle cleavage process are both investigated. The simulation result shows that there are different ductile-brittle behaviors in the cracks of different BCC materials. In the same loading range, the plastic deformation, such as dislocation nucleation and emission, stacking faults and twinning, is the main phenomenon for the crack of BCC-Ta. For the crack of BCC-Fe, plastic deformation and brittle cleavage are observed successively. At the initial stage, plastic deformation is dominant, which is similar to the crack of Ta. As loading increases, the crack begins to propagate, which differs from the crack of Ta. At first, the crack propagates along the initial direction [001], but then turns to [01] as the surface energy of {110} is lower than that of {01}. With the crack propagating, the crack tip is blunted by the plastic deformation, which is consistent with experimental results. As for BCC-W, the crack is found to propagate as brittle cleavage without plastic deformation at first. And the brittle cleavage is dominant all the time, which is a significant difference between W and the other two materials. In addition to the atomistic simulation, some theoretical calculations are also performed to analyze the ductile-brittle behaviors of the cracks. By an atomic slip model, the generalized stacking fault curves of BCC Ta, Fe and W are generated, which exhibit the unstable stacking fault energies of these materials. Based on the unstable stacking fault energy, two theoretical ductile-brittle criterions are analyzed. For the Rice-criterion, the result shows that the dislocation condition is met before cleavage for Ta and Fe, while for W the cleavage occurs before dislocation. For the ductile-brittle-parameter criterion, the result shows that Ta is the most ductile one in the three materials, followed by Fe, and W is the least ductile but the most brittle one. The analysis results of the two theoretical criterions both coincide well with the atomic simulation result, which well validates the simulation and fracture mechanisms.

Multiscale Analysis of Defect Initiation on the Atomistic Crack Tip in Body-Centered-Cubic Metal Ta

Advanced Numerical Characterization of Mono-Crystalline Copper with Defects

Multiscale Simulation of Mode II Atomistic Crack in BCC Tungsten

Discrete Twinning Dynamics and Size-Dependent Dislocation-to Twin Transition in Body-Centred Cubic Tungsten

The effect of crack orientation on fracture behavior of tantalum by multiscale simulation

Generalized Planar Fault Energy of Body-Centered Cubic Ta and Its Application to Plastic Deformation of Mode Ii Crack Tip

Multiscale Simulations and Ductile-Brittle Analyses of the Atomistic Cracks in Bcc Ta, Fe and W

In situ observation of dislocations at crack tip insingle crystalline tantalum

MULTISCALE MATERIALS MODELING METHOD AND ITS APPLICATION IN MATERIALS WITH DEFECTS

Nanoscale ductile fracture and associated atomistic mechanisms in a body-centered cubic refractory metal

In?situ TEM investigation of dislocation multiplication in front of crack in body?centered cubic single crystal niobium

A physically-based constitutive model for BCC metals and its application in tantalum

Cracking in a Fe–25Mn–3Si–3Al Steel

Modelling of dislocations, twins and crack-tips in HCP and BCC Ti

Two-way coupled modeling of dislocation substructure sensitive crystal plasticity and hydrogen diffusion at the crack tip of FCC single crystals

Molecular Dynamics Simulations of Pre-Crack Effects on Deformation and Failure Mechanisms for Pure Aluminum

Deciphering the interactions between single arm dislocation sources and coherent twin boundary in nickel bi-crystal

Molecular Dynamics Simulation of the Interaction Between Nanoscale Twin Boundaries and Partial Dislocations

Multiscale Analysis of Size Effect in Crystalline Solid Dislocation

Microscopic and macroscopic analyses of the interaction mechanism between defect growth and dislocation emission in single‐crystal aluminum

A Novel Mechanism for the Formation of Dislocation Cell Patterns in BCC Metal