Abstract:The plastic deformation behavior of metal plates has been proved to be affected by loading paths. Plastic flow is a critical component in the mechanical description of plastic deformation, like yield and hardening. In this work, the anisotropic plastic flow of two metal plates (16MnCr5 and S420MC) under non-proportional loading conditions was investigated. Large specimens manufactured along different orientations were pre-tensioned up to various strain levels; subsequently, small uniaxial tensile specimens were cut from the pre-tensioned specimens along different orientations with the interval of 15°, and then loaded to rupture. Meanwhile, the r-value, a measure of anisotropic plastic flow, was recorded. Result shows that for the studied plates which had constant r-value in the monotonic uniaxial tensile tests, a downward evolution of the r-value against plastic strain was observed when the Schmitt angle of two stage loading directions was greater than 90°. As the plastic strain in the subsequent loading stage accumulated, the r-value dropped from a higher level to its original level within a strain range about 6.0%. Based on the transient r-value evolution, a HEXAH-based evolutionary plastic potential model was constructed within the framework of non-associated flow (non-AF) theory. In the model, a local ellipse-shape distortion of the plastic potential surface was defined during plastic deformation process and when the Schmitt angel exceeded 90°, such distortion caused a downward evolution of the r-value in the subsequent deformation. The calibration result indicates that the model could reproduce the transient r-value response relevant to loading path change. The proposed evolutionary plastic potential model can be applied together with different anisotropic hardening models in the non-AF theory to give a detailed description of the plastic deformation behavior and hopefully provide a solution for the accurate simulation of the complex sheet metal forming process.

Plastic Flow Characteristics and Physically‐based Constitutive Modelling of Commercially Pure Vanadium

High Strain-Rate Response of Commercially Pure Vanadium

The Characteristics of Plastic Flow and a Physically-Based Model for 3003 Al–Mn Alloy Upon a Wide Range of Strain Rates and Temperatures

Plastic flow characteristics and constitutive relation of ultra high strength steel 18Ni250

A Review of Plastic Flow Characteristic and Constitutive Mode of Several Typical BCC Metals

PLASTIC FLOW CHARACTERISTICS AND CONSTITUTIVE RELATION FOR ULTRA HIGH STRENGTH STEEL AF1410

Plastic Flow Characteristics and Physical Conception Constitutive Relation for AZ31 Cast Magnesium Alloy

Flow Stress and Constitutive Model of OFHC Cu for Large Deformation, Different Temperatures and Different Strain Rates

PLASTIC FLOW STRESSES AND CONSTITUTIVE MODELS OF FOUR NEWER NAVAL VESSEL STEELS

Plastic Behavior and Constitutive Relations of DH-36 Steel over a Wide Spectrum of Strain Rates and Temperatures under Tension

Investigation on Plastic Flow Behaviors of FCC Polycrystalline Aluminum under Pre-Cyclic Tension-Compression Loading: Experiments and Crystal Plasticity Modeling.

Influences of Initial Porosity, Stress Triaxiality and Lode Parameter on Plastic Deformation and Ductile Fracture

Constitutive Modelling of Plasticity of Fcc Metals under Extremely High Strain Rates

The Plastic Flow Behavior and Model of Bcc Polycrystalline Metals with Application to Pure Ta, Mo, Nb and V

Hot deformation behavior of commercial pure vanadium

Plastic Flow Localization in Bulk-Tungsten with Ultrafine Microstructure

Experimental and Modeling Investigation on Anisotropic Plastic Flow of Metal Plates under Nonproportional Loading Conditions

Anisotropic plastic flow of low/medium carbon steel plates in different loading conditions: characterization of the r- value

Rheological Law and Constitutive Model for Superplastic Deformation of Ti-6Al-4V

Simulation of a Wrought Al-Cu-Mg-Ag Alloy During Hot Deformation Based on Constitutive Modelling and Process Maps

Research on Constitutive Models and Hot Workability of As-Homogenized Al-Zn-Mg-Cu Alloy During Isothermal Compression