Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Viscoelasticity of Concentrated Polyacrylonitrile Solutions: Effects of Solution Composition and Temperature

Viscoelastic Property Evolution of Thermoplastic Polyurethane During Annealing Treatment and Its Correlation with Segmental Crystallization

Study on the Viscosity of Polymer Polyol

Effects of Moisture Content and Heat Treatment on the Viscoelasticity and Gelation of Polyacrylonitrile/Dimethylsulfoxide Solutions

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Unusual Viscosity Behavior of Polyacrylonitrile in NaSCN Aqueous Solutions

Effect of Coagulation Conditions on the Radial Moduli of Polyacrylonitrile Nascent Fibers

Dynamic rheological studies of poly(p-phenyleneterephthalamide) and carbon nanotube blends in sulfuric acid.

Viscoelastic Study of Single Chain Cyclized Polymeric Nanoparticles and Linear Polymers Blends

Universal Concentration Scaling on Rheometric Properties of Polydisperse and High Molecular Weight Polyacrylamide Aqueous Solutions

Rheological properties of mixed polyacrylamide solutions

Effects of poly(vinyl alcohol) (PVA) concentration on rheological behavior of TEMPO-mediated oxidized cellulose nanofiber/PVA suspensions

Regulation of Rheological Behavior of Polyvinyl Alcohol Aqueous Solution by One-dimensional Particles

Interactions Between Polyacrylonitrile and Solvents: Density Functional Theory Study and Two-Dimensional Infrared Correlation Analysis.

New Insights into Orientation Differences Between Skin and Core Regions of Polyacrylonitrile Fibers During Pre-Stabilization with the Stretching Process

Effect of amorphous carbon on the tensile behavior of polyacrylonitrile (PAN)-based carbon fibers

Electrospinning of Polyacrylonitrile Fibers from Ionic Liquid Solution

Understanding the viscosity decline of poly(amic acid) solution from the correlation point of view

Study on the Formation Process of Polyacrylonitrile As‐spun Fiber

Steady Shear Viscosity and Oscillatory Complex Viscosity of Poly( P -Phenylene Terephthalamide) Solutions in Sulfuric Acid

High molecular weight effects on steady and transient rheology of lyotropic poly( p -phenylene terephthamide) solution