Abstract:The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy with lower processing temperature. In this study, the influence of SiC particle size and content on the properties of SiC/AlSi10Mg was systematically analyzed. SiC/AlSi10Mg composites were prepared by planetary ball milling, spark plasma sintering (SPS) and hot extrusion composite preparation process. The obtained composites presents dense microstructure without the formation of interfacial reaction phase. The distribution of micron SiC particles (μm-SiC) in the matrix is relatively uniform, and nano SiC particles (nm-SiC) slightly agglomerates with the increase of the content. The strength of SiC/AlSi10Mg increases with the increase of nm-SiC content, which is mainly attributed to dispersion strengthening, dislocation strengthening and grain refinement strengthening. The strength of SiC/AlSi10Mg hardly changes with the increase of μm-SiC content, but the elongation decreases gradually. The deformation between μm-SiC and AlSi10Mg matrix is not coordinated and μm-SiC cleave the AlSi10Mg matrix. The irregular boundaries of μm-SiC are easy to produce stress concentration during loading, leading to interface cracking or μm-SiC fracture. Therefore, μm-SiC are difficult to play a significant strengthening effect to composites. With the increase of SiC content, the fracture mechanism of composites gradually changes from ductile fracture to brittle fracture in SiC agglomeration region. This study lays a theoretical and experimental foundation for the controllable preparation and performance optimization of high strength and toughness AMCs reinforced by SiC particles.

Elongation Of Alpha-Sic Particles In Spark Plasma Sintered Alpha-Sialon/Alpha-Sic Composites

Synthesis of α-SiC/α-SiAlON composites by spark plasma sintering: Phase formation and microstructures development

Microstructure And Mechanical Properties Of The Alpha-Sialon/Alpha-Sic Composites: Effects Of Heat Treatment

Preparation Of Sic Ceramics By Spark Plasma Sintering

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

SiC-Al_2O_3 Nanocomposites Superfast Densified by SPS

Interfacial microstructure and sintering mechanism of plasma activated sintered Al/SiC composites

Microstructure and mechanical properties of the α-SiAlON/α-SiC composites: Effects of heat treatment

Microstructure and Mechanical Properties of the Spark Plasma Sintered Tac/Sic Composites: Effects of Sintering Temperatures

Spark plasma sintering of alumina/yttria‐doped silicon carbide

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

Preparation of tough ÃÂ¡-SiAlON ceramics by spark plasma sintering with ÃÂ¢-Si3N4 as raw materials

Microstructure and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>/SiC Nanocomposites Prepared by SPS

The dynamic properties of SiCp/Al composites fabricated by spark plasma sintering with powders prepared by mechanical alloying process

High plasticity achieved by spark plasma sintering method in aluminum matrix composites reinforced with Ti2AlC particles

Sintering And Mechanical Properties Of Aln-Rich Ceramics In The Sic-Aln System

Microstructure and Mechanical Properties of Unidirectional, Laminated Cf/SiC Composites with α-Al2O3 Nanoparticles as Filler

The interface reaction of SiC/Al composites by spark plasma sintering

Microstructure Characteristics And High-Temperature Performance Of In-Situ Reinforced Alpha-Sialon Ceramics

Mechanical properties and microstructure of laminated Si3N4+SiCw/BN+Al2O3 ceramics densified by spark plasma sintering

Microstructure compatibility and its effect on the mechanical properties of the α-SiC/β-Si3N4 co-reinforced barium aluminosilicate glass ceramic matrix composites