Abstract:Based on the development trends, graphitized carbon steel has been proposed as a low-sulfur and Pb-free free-cutting steel. This steel has attracted considerable attention because of its excellent cutting performance and good cold forging performance.This study investigates graphitized carbon steel containing 0. 46% C with ferrite and graphite. In particular, its compression deformation at room temperature was studied using a universal testing machine. The load-displacement curve was fitted, the drum shape and radial elongation of the end face of the compression specimens were calculated, the surface quality and microstructure of the compression specimens were observed using optical microscopy and field-emission scanning electron microscopy, and the micro-deformation of graphite particles and the ferritic matrix in the compression specimens was statistically analyzed using Image-Pro 6. 0. The results show that the tested steel exhibits good compression deformation performance. According to the varying characteristics of the load with respect to displacement, the compression deformation process of the tested steel is divided into two stages with a displacement of 7 mm (corresponding to 58. 3% reduction) : at the compression stage with displacement ≤7. 0 mm, the load increases linearly with displacement.The value of the drum shape increases with increasing displacement, reaching a maximum value of 14. 6%, the radial elongation of the end face of the compression sample increases 34%, and the Vickers hardness at the center of the compression sample reaches its maximum value of 38. 1 HV. At the compression stage with displacement > 7. 0 mm, the load increases exponentially, the value of the drum shape gradually decreases from its maximum value, the radial elongation of the end face of compression sample increases by 83. 1%compared with that at 7. 0 mm displacement, and the Vickers hardness at the center of the compression sample reaches its minimum value of 32. 7 HV. The aforementioned experimental data show that, in the compression process with displacement ≤7. 0 mm, the three non-uniform deformation zones within the compression sample are consistent with the traditional compression model; however, in the compression process with displacement > 7. 0 mm, the center of the sample is no longer the deformation zone with the largest deformation degree in the traditional compression model. That is, the deformation degree of the three nonuniform deformation zones changes at this stage. This change leads to sharp increase in the load and to a decrease in the drum shape. In addition, during the compression deformation process, the micro-deformation degree of the graphite particles is greater than that of the ferritic matrix in the three inhomogeneous deformation zones. This is attributed to the crystal structure of graphite. In particular, graphite has a layered, planar structure in which bonding between layers occurs via weak van der Waals interactions, which enables layers of graphite to be easily separated or to slide past each other.

The Mechanism of Expansion During the Baking of a Hot-Pressed Graphite Green Body

Pore Structure Evolution During the Coke Graphitization Process in a Blast Furnace

Evolution of Coke Microstructure and Metallurgical Properties During Graphitization in a Blast Furnace

Expansion Process and Thermal Conductivity Performance of the Graphite Used As the Heat and Mass Transfer Intensification Material

Effect of pore structure on the thermophysical and frictional properties of high-density graphite

Heat-treated Glassy Carbon under Pressure Exhibiting Superior Hardness, Strength and Elasticity

Anisotropic Thermal Conductivity and Permeability of Compacted Expanded Natural Graphite

Microstructure graphitization evolution and multi-scale, multi-mechanism synergistic enhancement of ultra-high strength carbon-graphite materials

Effects Of Heat-Treatment Temperature And Binder Content On The Microstructure And Thermal Conductivity Of Graphite Flake-Carbon Composites

Theoretical Model of Heating Patterns During Carbonization of Green Carbon Blocks

Effect of kneading and carbonization temperature on the structure of the carbon block for thermally conductive bulk graphites

Puffing behavior during the carbonization of lignin-collagen based green composites

Ultra-superior mechanical properties of multilayer graphene nanosheets reinforced carbon-graphite materials

Effects of Carbonization Pressure on Microstructure of Graphitized Pitch-derived Carbons

Inhomogeneous Deformation Behavior in Compressive Deformation Process at Room Temperature of Graphitized Carbon Steel

Preparation of the Sulfur-Free Expanded Graphite Using Induction Heating Method

Response surface optimization and finite element simulation to prepare microporous carbon refractories via cold isostatic pressing

Effect of Microstructural Change under Pressure during Isostatic Pressing on Mechanical and Electrical Properties of Isotropic Carbon Blocks

Binding Natural Graphite with Mesophase Pitch: A Promising Route to Future Carbon Blocks

Preparation of Siliconized Graphite by Liquid Silicon Infiltration of Porous Carbon Materials

Changes in Physical Properties with Varying Impregnation Temperatures and Compression Times During Fabrication of Carbon Blocks Using Needle Cokes and Pitch