Abstract:Magnesium alloys have received much attention for their lightweight and other excellent properties, such as low density, high specific strength, and good castability, for use in several industrial and commercial applications. However, both magnesium and its alloys show limited room-temperature formability owing to the limited number of slip systems associated with their hexagonal close-packed crystal structure. It is well known that crystallographic texture plays an important role in both plastic deformation and macroscopic anisotropy of magnesium alloys. Many authors have concentrated on improving the room- temperature formability of Mg alloys. However, despite having a lot of excellent properties in magnesium alloy, the study for various properties of magnesium alloy have not been clarified enough yet.Mg alloys are known to have a good damping capacity compared to other known metals and their alloys. Also, the damping properties of metals are generally recognized to be dependent on microstructural factors such as grain size and texture. However, there are very few studies on the relationship between the damping capacity and texture of Magnesium alloys. Therefore, in this study, specimens of the AZ31 magnesium alloy, were processed by hot working, and their texture and damping property investigated. A 60 mm × 60 mm × 40 mm rectangular plate was cut out by machining an ingot of AZ31 magnesium alloy (Mg-3Al-1Zn in mass%), and rolling was carried out at 673 K to a rolling reduction of 30%. Then, heat treatment was carried out at temperatures in the range of 573-723 K for durations in the range of 30-180 min. The samples were immediately quenched in oil after heat treatment to prevent any change in the microstructure. Texture was evaluated on the compression planes by the Schulz reflection method using nickel-filtered Cu Kα radiation. Electron backscatter diffraction measurements were conducted to observe the spatial distribution of various orientations. Specimens for damping capacity measurements were machined from the rolled specimen, to have a length of 120 mm, width of 20 mm, and thickness of 1 mm. The damping capacity was measured with a flexural internal friction measurement machine at room temperature. It was found that the damping capacity increases with both increasing heat-treatment temperature and time, due to grain growth and the increased pole densities of textures.

Effect of heating rates and loading rates on mechanical behaviors of magnesium alloy

Mechanical Behaviors of Magnesium Alloy AZ61 under Different Strain Rates and Heating Rates

Effect of Temperature and Heating Rate on Mechanical Properties of Magnesium Alloy AZ31

Effect of Heating-Rate on Failure Temperature of Pre-Loaded Magnesium Alloy

Ultimate Strength and Plasticity of Magnesium Alloy under Different Temperatures and Strain Rates

Investigations to the Effect of Heating-Rate on the Mechanical Properties of Aluminum Alloy LY12

Strain Rate and Temperature Effects on Formability and Microstructure of AZ31B Magnesium Alloy Sheet

Varying strain rates and elevated temperatures effects on the mechanical properties of AZ31B magnesium alloy

Effects of High Strain Rate on Mechanical Properties of As-extruded AZ61 Magnesium Alloy

Effect of Compression Loading Speeds on the Room Temperature Mechanical Properties of As-Extruded AZ31 Magnesium Alloy

Effect of Strain Rate on the Mechanical Properties of Magnesium Alloy AMX602

Effect of Heating-Rate on the Thermomechanical Behavior of Aluminum Alloy LY12 and a Phenomenological Description

Effect of Heating-Rate on Failure Temperature of Pre-Loaded Brass H62

Mechanical behavior of a lanthanum-doped magnesium alloy at different strain rates

Microstructure and Mechanical Behavior of Hot-Extruded Magnesium Alloy AZ91

Effects of Heating Rate and Temperature Holding Time on Mechanical Behaviors of Aluminum Alloy

An Experimental Investigation to the Effect of Heating Rate on the Failure of Pre-Load H62 Brass

Effect of Heat-Treating on Microstructure and High Cycle Bending Fatigue Behavior of AZ91 and AZE911 Magnesium Alloys

Mechanical Properties and Microstructure Evolution of AZ31 Magnesium Alloy Sheet Subjected to High Strain Rates Loading of Different Orientations

Effect of hot working on the damping capacity and mechanical properties of AZ31 magnesium alloy

Effect of Strain Rate and Temperature on Dynamic Mechanical Behavior and Microstructure Evolution of Ultra-High Strength Aluminum Alloy