Abstract:To explore the influence of the interface properties between fiber/cement matrix on the performance of fiber‐modified cement‐based composite. Polyethylene (PE) and polyvinyl alcohol fiber (PVA) are brought in the cement‐based materials to prepare mortar and Engineered Cementitious Composite (ECC) samples. The mortar's mechanical, and ECC's tensile capacity, four‐point bending and porosity were tested to verify the interface's influence on samples' performance. Furthermore, the water contact angle was used to analyze the wettability of the fiber, and a scanning electron microscope (SEM) was used to observe the fiber/matrix interface on the microscopic scale. Molecular dynamics simulation was performed to calculate the interfacial paraments from an atomic scale. The results shows that fiber increases the toughness of the mortar and improved its flexural strength. Through SEM, it was found that PVA fiber can form tight adsorption with the hydration matrix. While there are many apparent cracks and pores at the PE/matrix interface, the poor bonding destroys the matrix's structure and reduces its compressive strength. By analyzing the performance of ECC samples, it was known that PVA‐ECC's strain rate can reach 5.73%, while PE‐ECC is 4.20%. PE fiber has higher mechanical strength and can bear more loads, it helps PE‐ECC to obtain a greater modulus of rapture. Nuclear magnetic resonance results showed that the porosity of PVA‐ECC is lower than PE‐ECC. The ability of PE‐ECC to resist external interference is weak, and the interface of PE/matrix is easily damaged. Molecule dynamics simulation results indicated the adsorption energy between PVA/CSH is 6.17 times that of PE/CSH. The PVA/C‐S‐H interface tends to form CaO and H‐bonds to strengthen the bonding, the bonding has limited the movement of atoms and making the PVA chains tightly adsorbed on the CSH surface. While the adsorption between PE and CSH is weak, the PE will detach from the CSH surface and form aggregates. Moreover, PVA and water molecules form a stable hydrogen bond network to promote the hydration production grows on the surface of PVA fiber. However, PE fiber is complex enough to adsorb water molecules and hardly encourage the development of pores at the interface. By analyzing the properties of the interface between different fibers and cement matrix can provide insights for strengthening the interface properties of fiber cement matrix, and then improve the properties of fiber cement‐based composites.

FEM study on the shrinkage property of fiber reinforced mortar

Effect of Fiber on Mechanical Properties of Cement Stabilized Macadam Mixture

Influences of Fibers on Drying Shrinkage of Fiber-Reinforced Cementitious Composite

The Influence of Nano-Silica Composite Superabsorbent Polymer on the Autogenous Shrinkage of Mortar

Shrinkage of Extruded Fiber Reinforced Cement Mortar Board

Experimental Study and Mesoscale Finite Element Modeling of Elastic Modulus and Flexural Creep of Steel Fiber-Reinforced Mortar

Analytical Prediction and Experimental Research on Shrinkage Cracking of Restrained Early-Age Concrete

The Mechanical Properties of Polymer-cement Mortar

Performance Characteristics of Micro Fiber-Reinforced Ambient Cured One-Part Geopolymer Mortar for Repairing

Investigation on Shrinkage Characteristics of Polyester-Fiber-Reinforced Cement-Stabilized Concrete Considering Fiber Length and Content

A Study on the Mechanical and Wear-Resistance Properties of Hybrid Fiber Mortar Composites with Low Water-Cement Ratios

Shrinkage of high-performance fiber-reinforced concrete with adapted rheology

Impact of Polyvinyl Alcohol Fiber on the Full Life-Cycle Shrinkage of Cementitious Composite

Mechanism underlying effect of expansive agent and shrinkage reducing admixture on mechanical properties and fiber-matrix bonding of fiber-reinforced mortar

Influence of Polymer on Shrinkage and Anti-Cracking Performance of Mortar

Influence of polymer fibers on rheological properties of cement mortars

Shrinkage and Cracking Performance of PP/PVA Fiber-Reinforced 3D-Printed Mortar

Effect of shrinkage-mitigating materials on performance of fiber-reinforced concrete – An overview

Effect of interfacial properties between polyethylene and polyvinyl alcohol fiber/cement matrix on properties of mortar and ECC

Synergistic Effects of Ettringite-Based Expansive Agent and Polypropylene Fiber on Early-Age Anti-Shrinkage and Anti-Cracking Properties of Mortars

Investigation on the influence of fine steel fiber and carbon fiber on the thermo-mechanical properties of cement-based thermal energy storage mortar