Abstract:At present, the most prominent technical problems of small and medium capacity expanders are low internal efficiency and small expansion ratio. In order to promote the practical application of small and medium capacity Organic Rankine Cycle (ORC) system, improving the thermodynamic performance of the expander was a remarkable issue, and the systematic research on the irreversibility of expander's working process is the fundamental work to achieve this goal. Summarizing the related research on various small capacity volumetric expanders, the research on flow problem is lacked. For an atypical volumetric expander, the flow mechanism of single screw expanders (SSEs) is more complex. In this paper, we discussed the effect of the pressure loss in the inlet and exhaust passages on the performance of SSEs. We selected two SSE prototypes developed by our laboratory to carry out the experiment under variable working conditions. The internal volume ratios are 2.95 and 3.98 respectively. The pressure differences of inlet and exhaust passages were measured. In order to evaluate the effect of the flow losses on the performance, we defined two indexes: pressure loss rate (PLR) and pressure energy loss influence rate of shaft efficiency (PELRe). From the results, the pressure losses of inlet and exhaust passages for each SSE increase gradually, PLRin increases slightly and PLRout increases gradually. At the maximum point of shaft efficiency, the losses of the SSE with 2.95 are 28.06 kPa and 46.09 kPa, and the values of the SSE with 3.98 are 37.58 kPa and 33.79 kPa, respectively. It shows that the pressure losses are relatively high. The maximum values of internal and external expansion ratio for the SSE with 2.95 are 4.8 and 6 respectively, and the values of the SSE with 3.98 are 5.7 and 7 respectively. For ideal volume expansion, the internal expansion ratio of two prototypes should be 4.55 and 6.9, respectively. Summarizing the above results, how to enhance the pressure drop effect of leakage and reduce the flow resistance loss of inlet and exhaust passages simultaneously is an important technical premise to improve the expansion ratio by structural optimization. Meanwhile, PELRe of two prototypes are 16.01% and 13.59% respectively at the point. It shows that the flow losses of inlet and exhaust passages could significantly influence the performance of SSEs.

Investigation on the Rotary Vane Expander by Introducing High Pressure into Vane Slots

The new refrigeration system with vortex tube and ejector

Experimental Investigation of an Adjustable Ejector for Co2 Heat Pump Water Heaters

Experimental investigation on two-phase driven ejector performance in a novel ejector enhanced refrigeration system

Theoretical investigation on an ejector–expansion refrigeration cycle using zeotropic mixture R290/R600a for applications in domestic refrigerator/freezers

Design Optimization of A Small Scale High Expansion Ratio Organic Vapour Turbo Expander for Automotive Application

Performance of Rotary Compressor with Vapor Injection Mechanism on Blade

A Novel Vapor Injection Structure on the Blade of A Rotary Compressor

Experimental Research on Vapor-Injected Rotary Compressor Through End-Plate Injection Structure with Check Valve

Performance investigation and optimization analysis for vapor injection rotary compressor oriented to circular end-plate injection port without check valve

Experimental study on the influence of inlet and exhaust pressure loss on the performance of single screw expanders

Some Design Features of Co2 Swing Piston Expander

Performance Improvement of a Limaçon Gas Expander Using an Inlet Control Valve: Two Case Studies

Analysis, modeling and simulations of an innovative sliding vane rotary compressor with a rotating cylinder

Fluid-structure interaction analysis and optimization study of suction valves in small refrigeration compressors

Investigations on efficiency improvement of rolling piston type rotary compressor with a new-designed cylinder

An Enhanced Rotary Compressor with Gas Injection Through a Novel End-Plate Injection Structure

Experimental investigation of bladeless expander with an incompressible fluid

Experiments on a Small-Scale Axial Turbine Expander Used in CO2 Transcritical Power Cycle

Theoretical and experimental investigation on the rolling piston compressor with enhance vapor injection for heat pump system{fr}Etude théorique et expérimentale sur le compresseur à piston laminé avec injection de vapeur améliorée pour le système de pompe à chaleur

Numerical Investigation of Pressure Losses and its Effect During Intake in a Steam Wankel Expander