Abstract:Flow instability may happen in both subcritical two-phase flow boiling systems (such as U tube natural circulation steam generator of Pressurized Water Reactor, once through steam generator of High-Temperature GasCooled Reactor, etc) and supercritical evaporation systems. In previous theoretical researches, the model of a single heated tube (SHT) with constant pressure drop boundary condition (ConPD) was always used to investigate the system stability. However, in real applications, there are usually multiple parallel heated tubes (MHT) and unheated connection regions before the branch heated tubes. The system is usually driven by a pump, and there is always a long unheated main pipe and throttling between the heated tubes (boiler or steam generator) and the pump. However, there lacks rigorous analysis about the effects of these model simplifications and boundary conditions. Take superheated two-phase flow boiling systems as examples, the theoretical models with different flow-driven boundary conditions (ConPD, constant mass flow rate (ConMF), and pump driven (PumpD)), different numbers of heat tubes (SHT, MHT), with or ignoring the unheated region (UHR), with or ignoring the bypass of a pump, with identical or un-identical geometry parameters and operation parameters are established. Linear ordinary differential equations describing the instability are obtained. Eigenvalues of the coefficient matrix of linear ordinary differential equations, and the property of the block matrix and the similarity matrix are used to analyze the effects of the above boundary conditions and model simplifications on the system stability. Two new dimensionless numbers, dimensionless pump number (Npump) and dimensionless bypass number (Nbypass), are proposed to describe the effect of pump and its bypass on stability quantitatively. The effect of the pump bypass on the stability can be attributed to the decrease of Npump. No matter ConPD or PumpD is adopted, SHT considering UHR is proved to be more stable than SHT ignoring UHR. No matter UHR is considered or ignored, SHT with PumpD is proved to be more stable than SHT with ConPD. No matter UHR of MHT at the main pipe is considered or ignored, the stability of MHT with ConPD or ConMF or PumpD is proved to be the same as that of SHT with ConPD ignoring UHR. When ConPD ignoring UHR is adopted, the stability of MHT with un-identical geometry and operation parameters is proved to be the same as that of its most unstable heated tube. The above conclusions about the effect of model simplification and boundary condition are obtained from superheated two-phase flow boiling systems, they also hold for saturated two-phase flow boiling systems and supercritical evaporation systems.

Relationship Between the Heat Load and the Uneven Distribution Flow of the Manifold in Header System of Boiler

Two-phase Flow Oscillation and Distribution in Parallel Channels During R1233zd(E) Subcooled Flow Boiling: A Numerical Study

Effect of Inlet Flow Maldistribution on the Passage Arrangement Design of Multi-Stream Plate-Fin Heat Exchanger

Structural Optimizations of U‐ and Z‐Type Manifolds for Uniform Flow Distribution by Applying an Increaser and Baffle Plates

Safety Testing and Analysis of the Header of the Drawn Boiler with a Small Diameter and a Large Wall Thickness

Numerical investigation on flow distribution characteristics of U type and Z type manifold of cold box

Single-phase and Two-phase Flow and Heat Transfer in Microchannel Heat Sink with Various Manifold Arrangements

Flow Manifold Optimization for a Uniform Velocity Distribution in a Laminated Microreactor with Micro‐Pin‐Fin Arrays

A Comparative Numerical Study on Two-Phase Boiling Fluid Flow and Heat Transfer in the Microchannel Heat Sink with Different Manifold Arrangements

Theoretical Analysis on Hydrodynamic Characteristics of the Coil Tubes of Evaporating Heat-absorbing Surface in Boilers

THE EFFECTS OF WALL HEAT FLUX ARRANGEMENT ON FLOW INSTABILITY BOUNDARY IN A VERTICAL SINGLE TUBE

Effects of Manifold Designs on Flow and Thermal Performances of Microchannel Heat Sink

Investigation of flow and heat transfer performance of the manifold microchannel with different manifold arrangements

Numerical investigation on the thermal load heterogeneity of multi-assembly helical coil steam generator in high temperature gas-cooled reactor

Study on the flow and heat transfer characteristics of pin-fin manifold microchannel heat sink

Experimental study on effect of distribution of heating power density on stability of two phase flow

A general and rapid method to evaluate the effect of flow maldistribution on the performance of heat exchangers

Steam Temperature Characteristics in Boiler Water Wall Tubes Based on Furnace CFD and Hydrodynamic Coupling Model

Study on the uneven flow distribution and non-uniform heat transfer in microchannels

Numerical Investigation of Heat Transfer to Supercritical Pressure Water in Vertical Tube with Non-Uniform Heating Form

Theoretical analysis about model simplifications and boundary conditions on two-phase flow instability of parallel heated tube systems