Abstract:Carbon nanotubes (CNTs) have outstanding characteristics including high mechanical properties, namely tensile strength and elastic modulus,and still remarkable flexibility, excellent thermal and electric conductivities, low percolation thresholds (loading weight at which a sharp drop in resistivity occurs) and high aspect ratios (length to diameter ratio, L/D) while the latter provides the nanotubes with additional advantage over spherical fillers to obtain high property composites. Therefore I CNTs have the potential to act as a reinforcing filler of polymer matrices. The tetraglycidyl-4,4'-diaminodiphenylmethane (TGDDM) cured with 4,4'-diaminodiphenylsulphone WDS) and filled with graphite or carbon fibers are commonly used as a polymeric matrix in high performance composites employed in the aircraft and spacecraft industries. In present paper, multi-walled carbon nanotubes (MWNTs) as a nano-filler were incorporated in the TGDDM/DDS epoxy. The thermal properties of the composites were studied by differential scanning calorimetry (DSC), dynamic thermal analysis (DMTA) and thermal gravitimetric analysis TGA). In addition, the dispersion of MWNTs in the epoxy was also investigated by scanning electron microscopy SEM). In DSC studies, Kissinger and Flynn-Wall-Ozawa (FWO) methods were used to study the nonisothermal cure kinetics of the MWNTs filled TGDDM/DDS composites at different heating rates. The activation energy (E.) of cure reactions of the MWNTs filled epoxy composites was obtained by Kissinger and FWO methods. For all composites, the E. obtained by Kissinger method was slightly less than that of FWO method. With the addition of MWNTs, the E. of the epoxy composites decreased first and then increased with the increase of the MWNTs contents. These results showed that the incorporation of carbon nanotubes accelerated the cure reaction of the TGDDM/DDS epoxy at lower MWNTs content due to the interaction between the hydroxyl groups on the surface of nanotubes and the epoxy. However, due to the high surface energy of carbon nanotubes, the viscosity of MWNTs/epoxy composites increased at higher MWNTs content. Hence, the mobility of hydroxyl groups was hindered, and the reaction energy of composites increased with increasing MWNTs contents. The influence of carbon nanotubes on the thermal stability of the epoxy was studied by TGA. It is shown that MWNTs had little influence on the thermal stability of the cured epoxy. The storage modulus and glass transition temperature of MWNTs filled TGDDM/DDS were investigated by DMTA. It is seen that the storage modulus of TGDDM/DDS system was enhanced with the increasing of MWNTs content, that is, the modulus increased 6.3% and 7.8% at 1 wt % and 5 % MWNTs content, respectively. The glass transition temperature of the epoxy slightly decreased. Furthermore, the DMTA results of MWNTs/TGDDM/DDS composites were compared with that of carbon narrofibers (CNFs)/TGDDM/DDS composites. It was shown that the interactions between CNFs and epoxy were better those between that MWNTs and epoxy. The dispersion of carbon nanotubes in the epoxy was studied by SEM. The SEM results suggest that of MWNTs had poor dispersion in the cured epoxy. However, the radii of carbon nanotubes in the epoxy were greater than those of pure nanotubes. These results show the existence of interaction between carbon nanotubes and epoxy.

Morphology and Properties of Carbon Nanotubes Modified Epoxy

Thermo-Physical Properties of Epoxy Nanocomposites Reinforced with Amino-Functionalized Multi-Walled Carbon Nanotubes

Length-dependent Electrical and Thermal Properties of Carbon Nanotube-Loaded Epoxy Nanocomposites

Functionalization of Carbon Nanotubes by Corona‐Discharge Induced Graft Polymerization for the Reinforcement of Epoxy Nanocomposites

Reducing Dispersity of Mechanical Properties of Carbon Fiber/epoxy Composites by Introducing Multi-Walled Carbon Nanotubes

Effect of hydrophilically functionalized carbon nanotubes on the reinforcement of water-borne epoxy resin.

PREPARATION AND MECHANICAL PROPERTIES OF CARBON NANOTUBES/RESIN EPOXY COMPOSITE

Thermoanalytical Studies of High Performance Epoxy/Carbon Nanotube Composites

Preparation and Performance of MWNTs/ Epoxy Resins Composites

Thermo-mechanical properties of epoxy nanocomposites incorporating amino acid and acid functionalized multi-walled carbon nanotubes

THE EFFECT OF REACTIVE CARBON NANOTUBES ON T700 CARBON FIBER/EPOXY COMPOSITES

Spectroscopic study of double-walled carbon nanotubes functionalization for preparation of carbon nanotube / epoxy composites

The influence of functionalized MWCNT reinforcement on the thermomechanical properties and morphology of epoxy nanocomposites

Wear Performance of Tetrazine Modified Multiwalled Carbon Nanotube/Epoxy Composites

Morphological and Mechanical Properties of Bile Salt Modified Multi-Walled Carbon Nanotube/poly(vinyl Alcohol) Nanocomposites

Dispersion Stability of Functionalized MWCNT in the Epoxy–amine System and Its Effects on Mechanical and Interfacial Properties of Carbon Fiber Composites

Mechanical and thermal properties of high volume‐fraction carbon nanotube/epoxy composites, and property enhancement by UV ozone treatment of carbon nanotubes

Carboxyl-terminated Butadiene-Acrylonitrile-toughened Epoxy/carboxyl-Modified Carbon Nanotube Nanocomposites: Thermal and Mechanical Properties

Poly(methyl Methacrylate)-Decorated Single Wall Carbon Nanotube/epoxy Nanocomposites with Re-Agglomeration Networks: Rheology and Viscoelastic Damping Performance

Preparation and functional study of epoxy composites reinforced with ultra-low content single-walled carbon nanotubes

Reinforcement of Aminopropyl-Terminated Siloxane-Treated Carbon Nanotubes in Epoxy Thermosets: Mechanical and Thermal Properties