Abstract:As the lightest metallic structural material, magnesium alloys were widely used in automotive, aerospace, electronic equipment and other fields. Among commercial magnesium alloys, AM series were commonly used due to excellent ductility and energy absorption. However, their relatively poor strength greatly restricted their extended use. In order to improve mechanical properties of AM50 alloy, the Zn and Y elements were added into the AM50 alloy in the form of atomic ratio of 6:1 by the permanent mold casting. The microstructure, solidification behavior and mechanical properties of AM50-x(Zn, Y) (x=0, 2, 3, 4, 5, mass fraction, %) alloys were investigated by OM, SEM, EDS, XRD, thermal analysis and tensile tests. The results indicated that addition of Zn and Y elements with an atomic ratio of 6:1 to AM50 alloy, the microstructures were obviously refined, and the quasicrystal I-phase (Mg3Zn6Y) cannot form. In addition, the granular Al6YMn6 phase and fine Al2Y phase were formed in the microstructure, and the size of Al6YMn6 phase increased with increasing the Zn and Y content. The Phi-Mg-21(Zn, Al)(17) phase with lamellar structure was formed around beta phase when x >= 3, and its amount increased with increasing the Zn and Y addition. Thermal analysis results show that the Phi-Mg-21(Zn, Al)(17) phase was formed at 354 degrees C by the peritectic reaction, in which the precipitation temperatures of alpha-Mg and beta phase were decreased with the increase of x content. Due to the formation of Al6YMn6, Al2Y and Phi-Mg-21(Zn, Al)(17) phases, the size and amount of the beta phase was decreased. For AM50-4(Zn, Y) alloy, the microstructure was greatly refined, and the ultimate tensile strength, yield strength and elongation of the alloy reached to the maximum, 206.63 MPa, 92.50 MPa and 10.04%, respectively.

Thixoformability of a Mg–Gd–Y Magnesium Alloy and Its Mechanical Properties

Hot Deformation and Processing Map of As-Homogenized Mg–9Gd–3Y–2Zn–0.5Zr Alloy

Consideration of Castability and Formability for New Magnesium Alloys

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Microstructure Evolution During Reheating of Extruded Mg-Gd-Y-Zr Alloy into Semisolid State

Microstructure and Mechanical Properties of Extruded Mg–8.5Gd–2.3Y–1.8Ag–0.4Zr Alloy

Development of High Strength and High Thermal Conductivity Semi-Solid Magnesium Alloy by Thixomolding Process

Microstructures and Mechanical Properties of Mg-10Gd-3Y-2Zn-0.5Zr Alloy

Microstructures and mechanical properties of as-cast Mg–5Y–3Nd–Zr–xGd (x=0, 2 and 4wt.%) alloys

Study on Microstructures and Mechanical Properties of Die Casting Mg-xGd-3Y-0.5Zr Alloys

The Partial Substitution of Y with Gd on Microstructures and Mechanical Properties of As-Cast and As-Extruded Mg-10Zn-6Y-0.5Zr Alloy

Microstructures and Mechanical Properties of Extruded Mg-9Gd-4Y-0.6Zr-T5 at Elevated Temperatures

Microstructure evolution and tensile mechanical properties of thixoformed high performance Al-Zn-Mg-Cu alloy

Microstructure and mechanical properties of Mg-12Gd-5Y-1Sm-0.5Zr alloy

Microstructure and Mechanical Properties of Mg–6Gd–3Y–0.5Zr Alloy Processed by High-Vacuum Die-Casting

Preparation and Thixo-forming Characteristics of Mg-Al-Zn Semi-solid Alloy Billets

Microstructures and Properties of Mg–7Gd Alloy Containing Y

Microstructure, Mechanical Properties and Solidification Behavior of Am50-X(Zn, Y) Magnesium Alloys

Microstructure and Mechanical Properties of Moderate-Speed Extrudable Mg-Gd-Sm-Zr Alloy

Tuning texture and precipitation using Y/Gd atomic ratio in iso-concentration Mg–Y–Gd–Ag–Zr extruded alloys

Preparation of semi-solid billet of magnesium alloy and its thixoforming