Abstract:An ultrasonic vibration-assisted air-cooled stirring rod process (ACSR + UV) was used to efficiently prepare a large-volume semisolid slurry with a mass of more than 40 kg. A low-cost Al–Si–Fe–Mg–Cu–Zn die-casted alloy with high thermal conductivity, high plasticity and medium strength was developed. The alloy was used to manufacture large, thin-walled parts for 5G base stations by using the ACSR + UV rheological die-casting (ACSR + UV R-DC) process. Investigations were performed on the microstructure, porosity, mechanical properties, fracture behaviour and thermal conductivity of the ACSR + UV R-DC alloy, which was then compared to traditionally die-casted (T-DC) and ACSR R-DC alloys. The mechanisms for the microstructural refinement and enhancement of the mechanical and thermal conductivity performances of the ACSR + UV R-DC alloy were also analysed. The results showed that the ACSR + UV process increased the nucleation rate of the melt due to the increase in the nucleation area and the generation of cavitation bubbles. A radial- and an axial-forced convection was also generated inside the melt under the combined effects of acoustic flow and mechanical stirring, thereby homogenising the melt composition field and the temperature field. Therefore, the ACSR + UV R-DC process not only refined the primary α-Al (α1-Al), the eutectic silicon and the secondary α-Al (α2-Al), but also greatly improved the morphology and the distribution of the β-Al5FeSi phase. The mechanical properties of the ACSR + UV R-DC alloy were higher than those of the T-DC and the ACSR R-DC alloys. Compared to the T-DC alloy, the ultimate tensile strength, elongation and yield strength of the ACSR + UV R-DC alloy were increased by 34%, 122% and 19%, respectively. This was because the ACSR + UV R-DC technique gave the alloy the characteristics of high density, fine spherical α1-Al grain and a fine and uniform β-phase, which improved the fracture behaviour of the alloy. The thermal conductivity of the ACSR + UV R-DC alloy was 184 W/(m K), which was 10.2% and 3.4% higher than that of T-DC and ACSR R-DC alloys, respectively. This was because the refined eutectic silicon and β phases in the ACSR + UV R-DC alloy facilitated an easier electron flow through the eutectic region, and the decrease in porosity increased the effective area of heat conduction.

Preparation and Rheocasting of Semisolid Slurry of 5083 Al Alloy with Indirect Ultrasonic Vibration Process

New technique for preparing A356 alloy semisolid slurry and its rheo-diecast microstructure and properties

Study on a Semi-Solid Rheo-Diecasting Process With AZ91D Alloy Slurry

Efficient fabrication of semisolid nondendritic Al alloy slurry with high quality

On-line Preparation Technology of Semi-Solid Slurry of A356.2 Alloy

Rheoforming Processing of Al Alloys with Slurry Preparation System and Component Shaping System Apart

Industrialization of Aluminum Alloy Uniform Solidification Controlled Rheological Die Casting

Semi-Solid Slurries for Rheocasting of Hypoeutectic Al-Si-X Alloys Produced by Self-Stirring in Serpentine Channels

Influences of Master Alloys and Their Preparation Conditions on Microstructures of Semi-solid A356 Alloy Slurries

Solidification behavior and enhanced properties of semi-solid Al–8Si–0.5Fe alloys fabricated by rheo-diecasting

Development of Microstructure of Semi-Solid A356 Alloy by Alternating Electromagnetic Stirring

Synchronously Improving the Thermal Conductivity and Mechanical Properties of Al–Si–Fe–Mg–Cu–Zn Alloy Die Castings Through Ultrasonic-Assisted Rheoforming

Experimental Studies on Rheocasting Processing of A356 Alloy

Rheological Modeling of 7075 Aluminum Alloy Semi-Solid Slurry and its Application in the Simulation of SEED Rheocasting Process

Influence of Rheo-Diecasting Processing Parameters on Microstructure and Mechanical Properties of Hypereutectic Al–30%Si Alloy

Preparation of Al-5.8%Cu Alloy Semi-Solid Slurry by Controlled Melting

Microstructure characteristics and strengthening mechanism of semisolid CuSn10P1 alloys

Progress and Prospect of Research and Application of Semi-Solid Alloy Rheoforming Processes

Rapid Multiple Slurry-Preparation Technology of Melt Treatment and Reversible Electromagnetic Stirring

Enhanced comprehensive performance via alloying and rheo-diecasting in a semi-solid Al–Si–Fe–Mg–Cu–Sr alloy