Abstract:The present paper describes the study of the synergism between the matrix microstructure and reinforcement phase in electrodeposited nanocomposite coatings. Adding hard nanoparticles into the metallic matrix leads to hardening of the coating. The effects of particle load, size and dispersion on hardening as well as their influence on metal microstructure refinement were studied. The relative contributions of strengthening factors in Ni/nano-SiC composites, namely, Hall–Petch strengthening, Orowan strengthening, enhanced dislocation density and particles incorporation, were evaluated. The production of various coatings under different stirring conditions and powders resulted in dissimilarities in the incorporation of particles. The Hall–Petch relationship for pure nickel was determined using samples produced under different current densities. Additionally, the grain refinement resulting from the particle codeposition and agitation mode were identified as influential factors in grain-size strengthening. Dislocation density strengthening was significant in electrodeposits produced using ultrasonic agitation, while it was negligible in layers produced under other conditions. Particles codeposition affected the magnitude of Orowan strengthening, resulting in cases where strengthening was negligible despite the presence of particles. The sum of contributions and the modified Clyne methods were used to calculate the hardness of the composites based on the contribution of each strengthening factor, and the calculation results were in good agreement with experimental data. The wear behavior of the composites was analyzed by pin-on-disk measurements, and the results correlated with the strengthening mechanisms. Particle size, dispersion and content increased the strengthening effects as well as the hardness and wear resistance of the coatings.

Microstructure and Wear Resistance of Electrodeposited Ni-Sio2 Nano-Composite Coatings on Az91hp Magnesium Alloy Substrate

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Superior corrosion and wear resistance of AZ91D Mg alloy via electrodeposited SiO2–Ni-based composite coating

Microstructure, Friction and Wear Behavior and Corrosion Resistance of electroless Double-Layer Ni-P/Ni-Mo-P Coatings on AZ91D Magnesium Alloy

Preparation and properties of nano ZrO2 coating on magnesium alloy

Wear and Corrosion Properties of 316L-SiC Composite Coating Deposited by Cold Spray on Magnesium Alloy

Microstructure and mechanical properties of electroless Ni–P–Si 3 N 4 –TiN composite coatings

Study on Ni-P-nanoTiN Electroless Composite Coating

Electrodeposition and corrosion resistance of Ni–P–TiN composite coating on AZ91D magnesium alloy

Enhanced mechanical and wear properties of Ni-W-SiC composite coatings by synergistic influence of micro-nano SiC mixture

High Corrosion-Resistance Nanocrystalline Ni Coating on AZ91D Magnesium Alloy

Characterization and Wear Behaviors of Electrodeposited Ni-MoS2/SiC Composite Coating

Strengthening mechanisms and wear behavior of electrodeposited Ni–SiC nanocomposite coatings

Electrochemical Properties and XPS Analysis of Ni-B/SiC Nanocomposite Coatings

Microstructure, Friction, And Wear Properties Of Ni-Al2o3-Mos2 Composite Coatings

Corrosion resistance of AZ91D magnesium alloy with electroless plating pretreatment and Ni–TiO2 composite coating

Dry Sliding Tribological Behaviors of Electrodeposited Ni-GO/SiC Composite Coating on the 2218 Aluminum Alloy

Silica nanoparticles enhanced polysiloxane-modified nickel-based coatings on Mg alloy for robust superhydrophobicity and high corrosion resistance

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating

Wear resistance of Ni/nano-Al2O3 composite coatings by brush electroplating

Comparative study on the wear resistance and corrosion resistance of NiW and NiCoW composite coatings with micro- and nano-SiC particles