Abstract:Shot peening (SP) can modify the surface properties of titanium alloys and titanium matrix composites (TMCs). Based on our previous work in the last ten years, the microstructure and mechanical properties of SP treated Ti-6Al-4V (TC4) and (TiB+TiC)/TC4 are summarized in this review. The compressive residual stress (CRS) was formed on the surface after SP. At different SP intensities, the thickness of the surface CRS layer was improved with increasing SP intensities. During the stress peening, the CRS increased evidently, and the increment was proportional to the prestress. Besides, CRS's thermal relaxation was investigated, which showed that the CRS in the whole deformation layer was relaxed. The relaxation mechanism could be explained by the Zener-Wert-Avrami model. The microstrain, the domain size, and the dislocation density of the peened layer were investigated using the Voigt method. The domain size of TC4 was smaller than the composite, and the microstrain of the TC4 was higher than the composite. The average dislocation density was increased after SP due to the existence of reinforcements. Utilizing the Rietveld method to analyze the microstructure after SP, the variations were similar to the Voigt method's results. Also, the composite's stability was higher than TC4 because of the existence of reinforcements. Hardness analysis revealed that the existence of reinforcements raised the hardness. In the peened layer, the surface's hardness was maximum, and it decreased with the increase in depth. At the same temperature, the hardness of the TC4 was smaller than the composite counterpart. Finally, the strengthening mechanism of SP was discussed and summarized based on the above analysis.

Investigation on the Surface Layer Characteristics of Shot Peened Titanium Matrix Composite Utilizing X-ray Diffraction

Investigation on the Residual Stress and Microstructure of (tib+tic)/ti–6al–4v Composite after Shot Peening

Effect of shot peening on surface mechanical properties of TiB 2 /Al composite

Effects of shot peening on microstructure evolution and mechanical properties of surface nanocrystal layer on titanium matrix composite

The Variations of Microstructures and Hardness of Titanium Matrix Composite (tib + TiC)/Ti–6Al–4V after Shot Peening

Residual Stress Distribution And Microstructure Characterization Of Particle Reinforced Titanium Matrix Composite After Shot Peening Treatment: A Review

Numerical Analysis and Experimental Validation on Residual Stress Distribution of Titanium Matrix Composite after Shot Peening Treatment

Surface Microstructure Characterization on Shot Peened (tib + TiC)/Ti-6Al-4V by Rietveld Whole Pattern Fitting Method

Effect of Stress Peening on Surface Layer Characteristics of (tib + TiC)/Ti–6Al–4V Composite

Influence of Shot Blasting on Matrix Mechanical Properties of the Surface on TiB2/Al Composite

The Influence of Shot Peening on the Surface Properties of (Tib+tic)/ti–6al–4v

Investigation for recrystallization behavior of shot peened layer on TiB2/6351Al composite using X-ray diffraction

Surface shot peening of cast SiCw/Al composites

Investigation on Experiments and Numerical Modelling of the Residual Stress Distribution in Deformed Surface Layer of Ti–6Al–4V after Shot Peening

Surface Shot Peening of Cast SiC W /al Composites

Investigation on Microstructure and Properties of Al18B4O33 Whisker Reinforced AlMgSi Matrix Composite after Shot Peening

Residual stress and microstructure of the CNT/6061 composite after shot peening

Effect of surface high density twin microstructure induced by shot peening on the fatigue behavior of Ti-6Al-4V

Surface mechanical property and residual stress stability of nanostructured CNT/Al-Cu-Mg composites induced by shot peening

XRD ANALYSIS OF THE RECRYSTALLIZATION PROCESS OF SHOT PEENED LAYER ON IN SITU TIB2/6351AL COMPOSITE

Effect of the Conventional Shot Peening and Multiple Shot Peening on Microstructure and Residual Stress of TC17 Titanium Alloy