Abstract:Much of surplus ammunition stockpile inevitably requires demilitarized processing technology in the explosives industry. For the safe waste treatment and recycle, the thermoplastic polymer bonded explosive (PBX) can effectively reduce the military cost and non-conforming products. In addition, the thermoplastic PBX has excellent application prospect as the future explosive due to the good mechanical properties and insensitivity. However, for high solid content, most of thermoplastic PBXs still maintain a considerable viscosity even in high-temperature melting state, rendering traditional casting process unsuitable. In this study, a measuring method was adopted to accurately obtain the correlation of Pressure-Volume-Temperature (PVT) for the simulative materials of thermoplastic PBX at first. The equations of state for PVT and viscosity model were then created, which are of great significance in single screw extrusion. An experiment system of single screw extrusion was designed to implement the molding process considering the poor liquidity problem of the thermoplastic materials. Excellent molding stability (rho<0.5 % variation) was achieved for the extrusion system. Moreover, a numerical investigation was also performed. Good agreements were yielded by comparing the simulation data and experimental results. The effects of operational parameters, i. e., the entrance pressure, barrel temperature and rotation speed on molding process of the thermoplastic materials were investigated in detail. The wall shear stress decreases with the feed inlet well sealed whereas the maximum temperature rise increases a little due to limited thermal diffusion. Either increasing temperature or decreasing rotation speed is beneficial to overall process safety. However, production cycle and attainable molding density also need to be considered at the same time. Furthermore, the process parameters should be optimized on the basis of the PVT and viscosity properties of material in practice. The investigations above can be a better guidance for the development and implementation of thermoplastic PBXs molding process.

Theoretical and Experimental Study of the Melting Process of High‐density Polyethylene for Multidimensional Vibration Equipment

Studies on Nonisothermal Crystallization of Ultra–high Molecular Weight Polyethylene in Liquid Paraffin

A Constitutive Model for Strain Hardening Behavior of Predeformed Amorphous Polymers: Incorporating Dissipative Dynamics of Molecular Orientation

Microwave Heating and Devolatilization Characteristics of Polyethylene Particles in a Fixed‐bed Devolatilizer

Theoretical and Computational Analysis on the Melt Flow Behavior of Polylactic Acid in Material Extrusion Additive Manufacturing under Vibration Field

Modification of polypropylene by melt vibration blending with ultra high molecular weight polyethylene

Study on Crystallization Kinetics of Partially Melting Polyethylene Aiming to Improve Mechanical Properties

Melt Processing and Structural Manipulation of Highly Linear Disentangled Ultrahigh Molecular Weight Polyethylene

Modeling of the Molecular Weight Distribution and Short Chain Branching Distribution of Linear Low-Density Polyethylene from a Pilot Scale Gas Phase Polymerization Process

Steady-State Optimization Of An Industrial High-Density Polyethylene Slurry Process Based On An Equation-Oriented Molecular Weight Distribution Model

Measurement and Analysis on Tensile Strength and Crystallinity of Vibrating Extruded High-Density Polyethylene(Hdpe) Sheet

Improvement in an Analytical Approach for Modeling the Melting Process in Single-Screw Extruders

Numerical modelling of the viscoelastic polymer melt flow in material extrusion additive manufacturing

Finite Element Modeling of the Thermomechanical Behavior of Polyethylene

Effect of Vibration Parameters on Properties of Polypropylene in Dynamic Plasticizing Process

Modelling the Melting Kinetics of Polyetheretherketone Depending on Thermal History: Application to Additive Manufacturing

Stretch-Induced Melting And Recrystallization Of Polyethylene-Plasticizer Film Studied By In Situ X-Ray Scattering: A Thermodynamic Point Of View

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Experimental and Numerical Analysis of Single Screw Extrusion Process for Thermoplastic PBX Based on PVT Properties

An experimental‐based thermal prediction model for butt fusion welding of polymer pipes

Simultaneously achieving self-toughening and self-reinforcing of polyethylene on an industrial scale using volume-pulsation injection molding