Abstract:Effects of addition of cationic high molecular weight polymers (CP) as a primary flocculant or coagulant aid,,on the treatment efficiencies for raw water with low temperature (T10℃) and low turbidity (C010 NTU) were measured. The raw water was obtained from the Qujiang water treatment plant in Xi′an, China and investigated using a micro-flocculation depth-bed direct filtration process. Fractal mathematics and image analysis were used to analyze the effects of the following factors on treatment efficiencies: filter medium; raw water turbidity and temperature; chemical type, molecular weight and dosage of polymer; and mixing strength. The flocculation mechanism, floc morphologies and the fractal properties of floc structures were also compared after adding different flocculants. Five important results were obtained: ① It is not suitable to use Al2(SO4)3 (AS) or polyaluminium chloride (PAC) alone when T4℃, C04 NTU. Fine sand filter medium should be used if Al2(SO4)3 or PAC is added alone under the conditions 4℃T10℃, C010 NTU. For raw water with low temperature and turbidity, the flocs formed from inorganic coagulants are small, loose and fragile structures, with low efficient mass density and settling rate, but high fractal dimension. ②A coarse sand filter markedly improved CP flocculation efficiencies of raw water with low temperature and turbidity; but the mixing strength should be increased due to high viscosity of CP; ③It is appropriate to use low molecular weight polymers with weakly cationic properties or a lower dosage of CP with strong cationic properties if CP serves as a primary flocculant. When CP is used as a coagulant aid, the dosage of the primary coagulant can be greatly decreased, but it is better to use high molecular weight polymers with strong cationic properties or to increase the dosage of CP with weak cationic properties. ④The flocculation mechanisms of CP are charge neutralization, adsorption and bridging. Flocs formed from CP have have large network configurations, which lead to reduced sludge volumes and increased sludge settling rates as well as good dewatering behavior, but have a lower fractal dimension than inorganic flocs. ⑤ The treatment efficiencies of all tested flocculants are as follows: Al2(SO4)3 (or PAC) +CP CPPAC Al2(SO4)3 .

Treatment of Produced Wastewater from Polymer Flooding with Cationic Polymer Flocculant

Optimization of and Mechanism for the Coagulation–flocculation of Oil-Field Wastewater from Polymer Flooding

A novel interface-active cationic flocculant for the oil-water separation of oily wastewater produced from polymer flooding

Preparation of a selective flocculant for treatment of oily wastewater produced from polymer flooding and its flocculant mechanism

The effect of polymer on the floatation-flocculation performance of flocculant for treating polymer flooding produced water

Optimization and Characterization of Polysaccharide-Based Bioflocculant Produced by Paenibacillus Elgii B69 and Its Application in Wastewater Treatment

Produced Water from Polymer Flooding Process in Crude Oil Extraction: Characterization and Treatment by a Novel Crossflow Oil–water Separator

Influence of suspended microcrystalline polymer system on characteristics of produced water from High Ca and Mg oilfields and corresponding oil removal methods

Ultrasound-initiated synthesis of cationic polyacrylamide for oily wastewater treatment: Enhanced interaction between the flocculant and contaminants

Preparation of acrylate-modified cationic flocculant by polymer reaction and its performance in treating oilfield-produced water

Evaluation of newly developed reverse demulsifiers and cationic polyacrylamide flocculants for efficient treatment of oily produced water

[Effects of Polyacrylamide on Settling and Separation of Oil Droplets in Polymer Flooding Produced Water].

Study on Flocculant XN98 Treating with Oily Sewage from Polymer Flooding of Oilfield

Flocculation Efficiencies and Morphological Properties of Cationic Polymers in the Treatment of Low Temperature and Low Turbidity Raw Water

Optimal floc structure for effective dewatering of polymer treated oil sands tailings

Synthesis of a novel flocculant with dimethylamino propylmethacrylamide and polyether and its flocculation performance

Status of the treatment of produced water containing polymer in oilfields: A review

Preparation of Cationic Polyacrylamide Suspension and Its Application in Oilfield Wastewater Treatment

Flocculation and dewatering of the Kaolin slurry treated by single- and dual-polymer flocculants

Synthesis of hydrophobically modified flocculant by aqueous dispersion polymerization and its application in oily wastewater treatment

The analysis of formation of polymer‐containing oily sludge produced during the wastewater treatment in offshore oilfield