Abstract:A simple and convenient process was used to improve the utilization of natural limestone and kaolin for calcium looping technology and environmental applications. The calcined natural limestone modified with the distilled water (denoted as Limestone-W), was systematically studied and compared with the other CaO sorbents (calcium acetate, calcium D-gluconate and calcined natural limestone). These CaO-based sorbents were tested for their CO2 capture behavior through 20 carbonation/calcination cycles in a thermo-gravimetric analyzer (TGA). Their morphology, pore structure and phase composition before and after carbonation/calcination cycles were determined by scanning electron microscopy, nitrogen adsorption, and X-ray diffraction. The first-cycle and multicycle sorption results revealed that the Limestone-W sorbent exhibited a relatively faster reaction rate and higher cyclic CO2 capture. The characterization data indicated that the Limestone-W was composed of a special calcium oxide structure with lower crystalline and higher porosity nanoparticles, which appeared to be the main reasons for its higher CO2 capture capability. However, the Limestone-W still suffered loss of reactivity, even though it was less pronounced than the other CaO sorbent. To avoid this unfavorable effect, a thermally stable inert material (aluminum hydroxide derived from kaolin) was incorporated into the Limestone-W structure. This new sorbent revealed higher stability because the formation of a stable framework of Ca12Al14O33 particles hindered densification and sintering of the CaO phase. It was concluded that the combination of the distilled water modified limestone with Al(OH)(3) binder is a promising approach for synthesis of CaO-based sorbents with a higher reactivity. (C) 2014 Elsevier Ltd. All rights reserved.

CO2 capture of limestone modified by hydration-dehydration technology for carbonation/calcination looping

Modified CaO-based sorbent looping cycle for CO2 mitigation

High-temperature CO2 Capture Cycles of Hydrated Limestone Prepared with Aluminum (hydr)oxides Derived from Kaolin

Enhancement of Ca-Based Sorbent Multicyclic Behavior in Ca Looping Process for CO<sub>2</sub>Separation

CO2 Uptake of Modified Calcium-Based Sorbents in a Pressurized Carbonation–calcination Looping

Co2 Capture Using Cao Modified with Ethanol/Water Solution During Cyclic Calcination/Carbonation

Cyclic Calcination/carbonation Looping of Dolomite Modified with Acetic Acid for CO2 Capture

Reactivation of calcium-based sorbent by water hydration for CO2 capture

Calcium Looping Technology Using Improved Stability Nanostructured Sorbent For Cyclic Co2 Capture

CYCLIC CO2 CAPTURE BEHAVIOR OF LIMESTONE MODIFIED BY QINGHAI LAKE SALT DURING LONG-TERM CALCIUM LOOPING CYCLES

Steam Hydration Reactivation of Cao-Based Sorbent in Cyclic Carbonation/Calcination for Co2 Capture

Development and performance of CaO/La2O3 sorbents during calcium looping cycles for CO2 capture

Studies on CO2 uptake by CaO/Ca3Al2O6 sorbent in calcium looping cycles

Structurally Improved CaO-based Sorbent by Organic Acids for High Temperature CO2 Capture

Cyclic CO2 capture of CaO-based sorbent in the presence of metakaolin and aluminum (hydr)oxides

Macropore-Stabilized Limestone Sorbents Prepared by the Simultaneous Hydration–Impregnation Method for High-Temperature CO2 Capture

Enhanced CO 2 Capture Capacity of Limestone by Discontinuous Addition of Hydrogen Chloride in Carbonation at Calcium Looping Conditions

Study on Cyclic Carbonation Property of CaO-based Sorbents Modified With Fly Ash

Performance and Carbonation Kinetics of Modified CaO-Based Sorbents Derived from Different Precursors in Multiple CO2 Capture Cycles

Co2 Capture Performance of Calcium-Based Sorbents in A Pressurized Carbonation/Calcination Loop

Comparative investigation on CO2 uptake performance of limestone-derived sorbents with different supports synthesized by impregnated layer solution combustion method