Abstract:Summary Hybrid steam and in-situ-combustion (ISC) recovery processes have shown advantages over pure steam injection for recovery of oil-sands resources, particularly with respect to reducing costs and lowering requirements for water and natural-gas use. However, it has been very challenging to predict the field performance of hybrid steam-and-combustion processes with a reasonable degree of confidence. Usually, a combustion front has a thickness of only a few inches and high-resolution grids are required to capture steep temperature, saturation, and fluid-composition gradients in the vicinity of the combustion front. Using high-resolution, fine grids (FGs) in an entire reservoir to improve the accuracy of simulation can involve excessive computation time and, therefore, might be impractical for field-scale modeling. It is important to have a robust simulation tool to accurately predict reservoir performance without compromising the computational efficiency. In this work, numerical modeling of a hybrid steam-and-combustion recovery process was performed in a typical Athabasca Oil Sands reservoir. A comprehensive reaction-kinetics model derived from laboratory results was incorporated to represent the complex chemical reactions in the combustion process. This hybrid recovery process used oxygen-enriched air coinjection after several years of a steam-assisted-gravity-drainage (SAGD) operation. In the numerical model, safe limits were set on producing well temperature and oxygen content of the produced fluids. The initial grid size in the numerical model was at the centimeter scale, resulting in long run time, so to improve the computational efficiency a dynamic-gridding (DG) feature was applied. Parameters for controlling the creation of a dynamic grid and subsequently reverting back to a coarse grid have been examined to properly trigger the DG feature in the model. Once the optimized DG parameters were determined, operating parameters were investigated, including well configuration, oxygen (O2) concentration, and steam concentration. Comparisons were made between SAGD and hybrid steam/combustion processes in terms of cumulative water (steam) injection, cumulative oil production, and a cumulative steam/oil ratio (cSOR). By comparing the simulation results from an FG model and a DG model, we found that a temperature gradient is the best criterion to use for controlling DG compared to fluid-saturation and/or composition criteria. The threshold value for the temperature criterion was determined to be 35°C. The model locates the FGs in close proximity to the combustion front where the temperature and fluid-saturation gradients are the steepest and it places the coarse gridblocks elsewhere in the model. Comparisons are made between the computation time and the accuracy of simulation, and they demonstrate that dynamic grid amalgamation reduces the computation time significantly while maintaining reasonable computation accuracy of the simulation. Different well configurations affect O2-injection timing, combustion-front sweep efficiency and, therefore, the overall performance. The suggested O2 concentration in the hybrid process is between 10 and 20%. Steam can also be replaced with nitrogen (N2) to further improve the performance. For all simulation scenarios considered in this work, the cSOR in the hybrid process was improved, illustrating the main advantage of the hybrid approach over steam-only injection as in SAGD.

Design and Numerical Study of a New Hybrid CSS-SAGD Process Using Horizontal Wells for Recovering Heavy Oil

Numerical Thermal Simulation and Optimization of Hybrid CSS/SAGD Process in Long Lake with Lean Zones

Optimization of Geological Design for SAGD Process in Super Heavy Oil Reservoirs Using a Combination of Vertical and Horizontal Wells

Numerical Modelling of Hybrid Steam and In-Situ Combustion Performance for Oil Sands

Physical and Numerical Simulations of Steam Drive and Gravity Drainage Using the Confined Bottom Oil–Water Transition Zone to Develop Super Heavy Oil

Multi-stage development process and model of steam chamber for SAGD production in a heavy oil reservoir with an interlayer

A Model to Estimate Heat Efficiency in Steam-Assisted Gravity Drainage by Condensate and Initial Water Flow in Oil Sands

In-situ solvents generation enhanced steam assisted gravity drainage (ISSG-SAGD): A low carbon and high-efficiency approach for heavy oil recovery

Experimental Comparative Investigation of Hot Solvent/Steam-Assisted Gravity Drainage in Oil Sand Reservoirs

An innovative in situ solvent generation enhanced SAGD technique: Mechanism analysis based on numerical simulation

A semi-analytical model based on unsteady conductive heat transfer in steam-assisted gravity drainage (SAGD)

Experimental Study on Well Placement Optimization for Steam-Assisted Gravity Drainage to Enhance Recovery of Thin Layer Oil Sand Reservoirs

A New Method to Reduce Shale Barrier Effect on SAGD Process: Experimental and Numerical Simulation Studies Using Laboratory-Scale Model

Visualization Experimental Study on Well Spacing Optimization of SAGD with a Combination of Vertical and Horizontal Wells

A Simple Normalized Analytical Model for Oil Production of SAGD Process and Its Applications in Athabasca Oil Sands

Experimental Investigation and Numerical Simulation of Dynamic Characteristics for Multithermal Fluid-Assisted SAGD in Extraheavy Oil Reservoir

Experimental and simulation studies on steam stimulation with multiple fluids for offshore heavy oil reservoirs

Experimental and numerical investigation on extra-heavy oil recovery by steam injection using vertical injector -horizontal producer

Field-Scale Modeling of Hybrid Steam and In-Situ-Combustion Recovery Process in Oil-Sands Reservoirs Using Dynamic Gridding

A Critical Review of Reservoir Simulation Applications in Key Thermal Recovery Processes: Lessons, Opportunities, and Challenges

Study of Novel Steam Assisted Gravity Drainage Multilateral Wells with Dynamic Gridding