Abstract:Nano-sized aluminum (Nano-Al) powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time. However, the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear. In this study, the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics, detonation reaction zone, and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test, detonation pressure test, explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry. Lithium fluoride (LiF), which has an inert behavior during the explosion, was used as a control to compare the contribution of the reaction of aluminum. A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn. Combining the numerical simulations based on the calculated afterburn energy and experimental results, the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated. This study found that when the 170 nm Al content is from 0% to 15%, every 5% increase of aluminum resulted in about a 1.3% decrease in detonation velocity. Manganin pressure gauge measurement showed no significant enhancement in detonation pressure. The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm, which is respectively 14% and 8% higher than that of RDX/wax/95/5 explosive (57 ns and 0.39 mm). Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front. For the recording time of about 10 μs throughout the plate push test duration, the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12% and 2.9 μs higher than that of RDX/LiF/wax/80/15/5, respectively, indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive. Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume, over 80% of the aluminum had reacted, implying very high reactivity. These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.

Energy Output and Mechanical Strength of Aluminum-Fibre-reinforced Composite Explosives

Effects of Nano Aluminum Powder on the Mechanical Sensitivity of RDX-Based Explosives

Influence of Al Content and Surrounding Medium on the Energy Output of Cyclotrimethylenetrinitramine (rdx)/al/wax Explosives

Anti-explosion Tests and Numerical Simulations of Ultra-High Toughness Cementitious Composites Subjected to Blast by Embedded Explosives

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Experimental Investigation on the Enhancing Effect of Reactive Materials on Explosion Fireballs and Shock Waves of Composite Charges

Effect of microstructure on functional force and air explosion performance of CL-20-based aluminum-containing explosive

The Role of Al Reaction Rate in the Damage Effect and Energy Output of RDX‐Based Aluminized Explosives in Concrete

Semi‐closed Investigations of New Aluminized Thermobaric and Enhanced Blast Composites

Preparation, High-Density Spherical, and Low Sensitivity of RDX/NC/PMMA Composite Particles

Deflagration to detonation transition in weakly confined conditions for a type of potentially novel green primary explosive: Al/Fe2O3/RDX hybrid nanocomposites

A Method to Investigate the Confined Explosion of Thermobaric and Enhanced Blast Explosives

Explosion Temperature and Dispersion Characteristics of Composite Charges Based on Different Non-detonative Materials

Study on Energy Output Characteristics of Aluminized Emulsion Explosive

The effect of Mg(BH4)2 on the energy characteristics of RDX based aluminized explosives

The Physical-Mechanical Properties of Aluminum Nanocomposites Produced by High Energy Explosion Impact

Effect of metal dust fuel at a low concentration on explosive/air explosion characteristics

Investigation on Anti-Explosion Performance of Reinforced Concrete Slab with Composite Protective Aluminum Foam

On weak influence of aluminum powder size on its post-detonation reaction in different time scales

Effect of the Addition of Steel Fibers on the Bonding Interface and Tensile Properties of Explosion-Welded 2A12 Aluminum Alloy and SS-304 Steel

Internal Explosion Performance of RDX@Nano-B Composite Explosives