Abstract:Nano-sized aluminum (Nano-Al) powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time. However, the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear. In this study, the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics, detonation reaction zone, and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test, detonation pressure test, explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry. Lithium fluoride (LiF), which has an inert behavior during the explosion, was used as a control to compare the contribution of the reaction of aluminum. A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn. Combining the numerical simulations based on the calculated afterburn energy and experimental results, the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated. This study found that when the 170 nm Al content is from 0% to 15%, every 5% increase of aluminum resulted in about a 1.3% decrease in detonation velocity. Manganin pressure gauge measurement showed no significant enhancement in detonation pressure. The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm, which is respectively 14% and 8% higher than that of RDX/wax/95/5 explosive (57 ns and 0.39 mm). Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front. For the recording time of about 10 μs throughout the plate push test duration, the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12% and 2.9 μs higher than that of RDX/LiF/wax/80/15/5, respectively, indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive. Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume, over 80% of the aluminum had reacted, implying very high reactivity. These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.

Deflagration to detonation transition in weakly confined conditions for a type of potentially novel green primary explosive: Al/Fe2O3/RDX hybrid nanocomposites

Shock Response of 1,3,5-Trinitroperhydro-1,3,5-triazine (RDX): the C-N Bond Scission Studied by Molecular Dynamics Simulations

Effect of low-concentration RDX dust on solid–liquid mixed fuel characteristics

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Research of detonation products of RDX/Al from the perspective of composition

Enhancing RDX Thermal Decomposition in Al@RDX Composites with Co Transition Metal Interfacial Layer

Activation and reaction mechanism of nano‐aluminized explosives under shock wave

Ultrafine RDX / Al Preparation and Properties of Mixed Explosives

On weak influence of aluminum powder size on its post-detonation reaction in different time scales

Preparation, High-Density Spherical, and Low Sensitivity of RDX/NC/PMMA Composite Particles

Reactive molecular dynamics simulation of thermal decomposition for nano-AlH3/TNT and nano-AlH3/CL-20 composites

Electrostatic spraying synthesis of energetic RDX@NGEC nanocomposites

Molecular dynamics study on the thermal decomposition of 1,3,5-trinitro-1,3,5-triazinane (RDX) catalyzed by aluminum nanoparticles with different contents

Effects of Nano Aluminum Powder on the Mechanical Sensitivity of RDX-Based Explosives

A novel nano-thermite system with BiOF as fluorine-containing oxidant for enhanced energy release performance

The enhanced catalytic decomposition behaviors of RDX by using porous activated carbon loaded with nanosized metal oxides

Mechanochemical fabrication and properties of CL-20/RDX nano co/mixed crystals

Influence of a novel nano-thermite colloid based on CuO coated CNTs on the thermo-analytical characteristics of 1,3,5-trinitro-1,3,5-triazinane

Using microfluidic technology to prepare octogen high-energy microspheres containing copper-aluminum composite particles with enhanced combustion performance

Al/CuF 2 Composite Materials with Ignition Characteristics and Pressure Output Ability for Nanothermites

In Situ Preparation of Explosive Embedded CuO/Al/CL20 Nanoenergetic Composite with Enhanced Reactivity