Abstract:Nanosized copper oxide-zirconia particles containing 10-30 mol% of copper were prepared by using a precipitation technique in aqueous tetramethylammonium hydroxide solutions. Two methods, in situ (INS) and step-by-step (SBS), which differed in the time when the copper salt was introduced to the synthesis procedure, were used, and this allowed a comparison of the properties of the final powders produced using the two modes of preparation. The surface areas and phase compositions were different for the samples prepared from the two different methods after calcination at 500 degreesC. A surface area of 168 m(2) g(-1) was obtained for the sample prepared with the SBS method and 121 m(2) g(-1) for the INS method, both contain 30 mol% copper. Tetragonal ZrO2 was observed from X-ray diffraction patterns for all samples prepared with the SBS method, however, no separate phase of copper or copper oxide was observed. It is proposed that all of the copper is finely distributed on the surface of the ZrO2 particles with the SBS method. For the samples prepared from the INS method, tetragonal ZrO2 was obtained at a low copper content and the peaks indexed to tetragonal ZrO2 shifted to higher angle with the increase of copper content, indicating copper ions being incorporated into the lattice. An amorphous compound was obtained at high copper content (30 mol%). The phase change with the calcination temperature was also investigated for the INS sample containing 30 mol% copper. The studies show that tetragonal ZrO2 and copper oxide were present after calcination at 400 degreesC, and tetragonal ZrO2 with a small amount of monoclinic ZrO2, as well as copper oxide, formed after calcination at 700 degreesC. However, after heating at 500 degreesC, amorphous compounds were obtained, suggesting that 500 degreesC could be a phase transition point. The incorporation of copper in the ZrO2 lattice resulted in a loss of order in the ZrO2 structure when calcined at 500 degreesC, with a further increase in the calcination temperature leading to the phase change.

Preparation and Characterization of CuO Nanoparticles with Different Size and Morphology

Influence of Interphase Distribution of Reactants on Preparation of Nano-CuO by Adsorption Phase Technique

Morphology Investigation of Hydrothermally Prepared ZnO Micro-Crystals Influenced by Cu2+ Ions

The Convenient Preparation of Porous CuO Via Copper Oxalate Precursor

Morphology Control Of Cuo Micro-Particles Using Zn2+ Ion And Ultrasonic Treatment

Preparation and microstructure of nano-sized Cu particles by mechanochemical reaction

Study on Preparation of Copper Oxide Nanopowders

Preparation of Ultrafine Cu 2 O Powders with Different Morphologies from Cu(OH) 2 Gel

Preparation and Characterization of CuO Nanorods by Thermal Decomposition of CuC2O4 Precursor

A novel wet-chemical method of preparing highly monodispersed Cu2O nanoparticles

Preparation of CuO Nanoparticles by Microwave Irradiation

Sonochemical Preparation of Micro- and Nanometer Cu2O

Controlled Synthesis Of Monodispersed Cuo Nanocrystals

One-Pot Fast Synthesis of Leaf-Like CuO Nanostructures and CuO/Ag Microspheres with Photocatalytic Application

A Simple Method for the Preparation of Cu2O with Different Morphologies in High Reaction Concentrations

Preparation of Nanopowder CuO by Mechanochemical Processing in the Solvent of Ethylene Glycol

Novel Way to Synthesize CuO Nanocrystals with Various Morphologies

Microwave-Assisted Hydrothermal Preparation of Flower-Like CuO

Preparation and characterization of hierarchical nanostructures composed by CuO nanowires within directional microporous Cu

Preparation of Cu2O Hollow Nanospheres under Reflux Conditions

Preparation and characterization of CuO–ZrO2 nanopowders