Abstract:Ti-2Al-2.5Zr alloy with hcp structure is a kind of structural materials used under low temperature condition, e.g. pipeline system of liquid hydrogen and liquid oxygen in missile engine. It is usually serviced in condition of severe low temperature and dynamic loading. Deformation twinning is a common and important plastic deformation mode in the hexagonal close-packed alloy., but will be severely restricted as the grain is refined from tens of microns to a few microns. On the other hand, twinning has a low sensitivity to temperature, consequently becomes a favorable deformation mode at low temperature in comparison with dislocation slip. The objective of this work is to study the coupling effect of grain refinement and testing temperature on twinning behavior and the low-cycle fatigue behavior of Ti-2Al-2.5Zr.Symmetrical push-pull low-cycle fatigue (LCF) tests were performed on Ti-2Al-2.5Zr with grain size of about 5 pm at room temperature (RT) and low temperature (77 K). The results show that the alloy exhibits the higher ductility and the longer low-cycle fatigue life at 77 K than those at RT. The cyclic stress response curves show that the cyclic softening occurs at the low strain amplitudes of 0.5% and 1.0%. However, as strain amplitude increased to 1.5% and 2.0%, cyclic stress saturation appeared. When testing temperature declined to 77 K, the cyclic hardening was observed at all four strain amplitudes. The degree of cyclic hardening increases as the strain amplitude rises. The fractography analyses suggest that transgranular fracture with well-developed fatigue striations is the predominant failure mode. The amount of secondary cracks is much higher in the alloys deformed at RT than that at 77 K. TEM examination reveals that deformation twins become more active. The primary types of twinning are {10 (1) over bar1} and {11 (2) over bar1}. The typical deformation microstructures consist of individual dislocation lines together with the tangled dislocation at the low strain amplitudes of 0.5% and 1.0%. As the strain amplitude increased to 1.5% and 2.0%, {10 (1) over bar0} prismatic slip and {11 (2) over bar1} pyramidal slip were simultaneously activated, the subgrain and dislocation cells were formed. At 77 K and strain amplitude of 2.0%, the parallel dislocation bands distribute along prismatic plane. As the strain amplitude increased to 4.5%, mutua l perpendicular dislocation lines appeared. The improvement of fatigue life of Ti-2Al-2.5Zr at 77 K is attributed to the constraint of inhomogeneous slip and the activation of deformation twinning.

Fatigue properties and deformation mechanism of Ti2.5Cu alloy

Unexpected Dynamic Recrystallization Behavior of Ti-7Cu Alloy in Semi-Solid State

Mechanical Behavior and Deformation Mechanisms of Ti–2.5Cu Alloy Reinforced by Nano-Scale Precipitates at 293 and 77 K

Monotonic and cyclic behavior of Ti–2.5Cu alloy at room temperature (293 K) and at 77 K

Tensile and low-cycle fatigue behavior of commercially pure titanium and Ti–5Al–2.5Sn alloy at 293 and 77 K

LOW CYCLE FATIGUE BEHAVIORS AND MICROSTRUCTURES OF Ti–2Al–2.5Zr WITH FINE GRAIN AT RT AND 77 K

Low-cycle fatigue behavior and deformation substructure of Ti-2Al-2.5Zr alloy at 673 K

Age Hardening and Its Modeling of Ti–2.5Cualloy

Precipitation Behavior and Tensile Properties of Stress-Aged Ti-2.5Cu Alloy

Low-cycle Fatigue Behavior and Deformation Substructure of Ti-2Al-2.5Zr Alloy at 673K

Low-Cycle Fatigue Behavior and Deformation Substructure of Ti-2al-2.5zr Alloy at 298 and 673K

Microstructure stability and damage mechanisms in an α/β Ti-6Al-4V-0.55Fe alloy during low cycle dwell-fatigue at room temperature

Isothermal and thermomechanical fatigue behavior of Ti-2Al-2.5Zr titanium alloy

Effect of deformation and aging treatment on the microstructure and properties of Cu-0.45Cr-0.14Ti (wt.%) alloy

Deformation mechanisms in a TiNi shape memory alloy during cyclic loading

Microstructures, Martensitic Transformation and Shape Memory Behaviors of Aged Ti50.5Ni33.5Cu11.5Pd4.5 Alloys

High Temperature Low Cycle Fatigue Properties and Failure Mechanism of a TiAl Alloy

Effect of Grain Size and Testing Temperature on Low-Cycle Fatigue Behavior and Plastic Deformation Mode of Ti-2Al-2.5Zr

Mechanical Properties and Deformation Mechanisms in Microscale Ti-55531 Alloy

Dynamic Fracture Toughness of Ti–2.5Cu Alloy Strengthened with Nano-Scale Particles at Room and Low Temperatures

Effect of Grain Size on Twinning Behavior in Ti–2Al–2.5Zr Alloy Fatigued at 77K