Abstract:The superconducting magnet group at IHEP (the Institute of High Energy Physics, Chinese Academy of Sciences, China) has been engaging in the R&D of high field accelerator magnets since 2014 for the pre-study of the next-generation high energy particle accelerators like CEPC-SPPC (Circular Electron Positron Collider-Super Proton Proton Collider), FCC (Future Circular Collider), etc. A superconducting model dipole magnet named LPF1 was first fabricated with NbTi and Nb 3 Sn in a combined common-coil configuration in 2017 and tested in 2018, a main field of 10.23 T was reached within two 10 mm apertures. The magnet was reassembled with higher pre-stress in 2019 to investigate the influence of the pre-stress loading level on the performance of common-coil dipole magnets. The main field of this upgraded magnet named LPF1-S was increased to 10.71 T within two 12 mm apertures. By improving the key processing technologies in Rutherford cable fabrication, coil winding, Nb 3 Sn & NbTi splices soldering and coil impregnation, the recently fabricated model dipole magnet named LPF1-U attained a 12.47 T main field in two 14 mm apertures in 2021. To fully take advantage of Nb 3 Sn and NbTi superconductors in different field regions, LPF1-U was still designed and developed with a combined coil configuration with Nb 3 Sn for the inner two coils and NbTi for the outer four coils. Additionally, graded coil topology and different coil LSS (length of straight section) settings were adopted in the optimization of LPF1-U layouts. Bladder and key technology was used for the support structure, and fiber optic sensors based on FBG (fiber Bragg grating) were utilized to monitor the stress distribution and variation in the structures and coils through the whole process from magnet assembly to cool-down and excitation. During the performance test, a relatively large number of trainings were carried out and LPF1-U became more stable after the thermal cycle. A peak field of 12.7 T in the coils (12.47 T main field in apertures) corresponds to an operating current of 6865 A and a load line ratio of 90% was finally attained. It is worth mentioning that LPF1-U is the first hybrid—Nb 3 Sn, NbTi—common coil dipole magnet that has achieved a main field of more than 12 T in two apertures. The design, fabrication and performance analysis of the LPF series dipole magnets are presented in this paper.

Design and Experiments of 65 T High Field Pulsed Magnet

Concept Design of 100 T Pulsed Magnet at the Wuhan National High Magnetic Field Center

Design and Test of a 90-T Nondestructive Magnet at the Wuhan National High Magnetic Field Center

Design and Performance of the First Dual-Coil Magnet at the Wuhan National High Magnetic Field Center

Mechanical Design, Assembly and Strain Measurement Results of a 13-T Superconducting Dipole Magnet

Development of Superconducting Model Dipole Magnets Beyond 12 T with a Combined Common-Coil Configuration

20 T Dipole Magnet Based on Hybrid HTS/LTS Cos-Theta Coils with Stress Management

High Temperature Superconducting Magnet for Fast Discharging Experiments

Design and Fabrication of a 13-T Twin-Aperture Superconducting Dipole Magnet with Graded Common-Coil Configuration

Development of YBCO Insert for a 25 T All Superconducting Magnet

45.5-tesla direct-current magnetic field generated with a high-temperature superconducting magnet

Simulation and experiments of Stacks of High Temperature Superconducting Coated Conductors Magnetized by Pulsed Field Magnetization with Multi-Pulse Technique

Short and Long Pulse High Magnetic Field Facility at the Wuhan National High Magnetic Field Center

The Conceptual Optimal Design of a 300MJ High Temperature Superconducting Magnet

Strain analysis and preliminary test of an all-superconducting high-field magnet generating 32.4 T direct-current magnetic field

A 7 T Pulsed Magnetic Field Generator for Magnetized Laser Plasma Experiments

The Design and Winding Method of A Conduction-Cooled 1.5 T Bi-2223 High Temperature Superconducting Magnet

Practical technique of pulsed field magnetization for bulk HTS application

An in-situ magnetising holder achieving 1.5 T in-plane field in 200 kV transmission electron microscope

Design and Preliminary Tests of a 20-T REBCO Insert Coil for a 35-T All Superconducting Magnet

Design and Testing of a Prototype Canted-Cosine-Theta HTS Dipole Magnet Using CORC Cable