Abstract:A cement paste or mortar is composed of a mineral skeleton with micron to millimeter-sized grains, surrounded by water filaments. The cohesion or shear resistance in the cement paste and mortar is caused by capillary forces of action. In the case of mortar mixes, there is friction between the particles. Therefore, the mortar mixture shows both friction between particles and cohesion, while the paste shows only cohesion, and the friction between particles is negligible. The property of the cement paste is greatly influenced by the rheological characteristics like cohesion and internal angle friction. It is also interesting that when studying the rheology of fresh concrete, the rheological behavior of cement paste and mortar has direct applicability. In this paper, the rheological characteristics of cement paste and mortar with and without mineral admixtures, that is, fly ash and ground granulated blast-furnace slag (GGBS), were studied. A cement mortar mix with a cement-to-sand ratio of 1:3 was investigated, including fly ash replacement from 10% to 40%, and GGBS from 10% to 70% of the weight of the cement. A suitable blend of fly ash, GGBS, and ordinary Portland cement (OPC) was also selected to determine rheological parameters. For mortar mixtures, the flow table was conducted for workability studies. The flexural and split tensile strength tests were conducted on various mortar mixtures for different curing times. The results indicate that in the presence of a mineral mixture of fly ash and GGBS, the rheological behavior of paste and mortar is similar. Compared with OPC-GGBS-based mixtures, both cement with fly ash and ternary mixtures show less shear resistance or impact resistance. The rheological behavior of the mortar also matches the rheological behavior in the flow table test. Therefore, it is easy to use the vane shear test equipment to conduct cohesion studies to understand the properties of cement paste and mortar using mineral admixtures. The strength results show that the long-term strength of GGBS-based mixtures and ternary mixed mixtures is better than that of fly-ash-based mixtures. For all mixtures, the strength characteristics are greatest at a w/b ratio of 0.6.

Ultrafiltration of Bamboo Pulp Black Liquor Modified by Graft Sulfonation and Water-Reducing Dispersion Performance of Fractions

Research on Sustainable Development of Fine-Grained Material Cement Slurry

Effect of Additives on the Rheological and Mechanical Properties of Microfine-Cement-Based Grout

Optimization on overall performance of Modified Ultrafine Cementitious Grout Materials (MUCG) and hydration mechanism analysis

Rheological properties and microstructure of fresh cement pastes with varied dispersion media and superplasticizers

A Novel Gypsum-Based Self-Leveling Mortar Produced by Phosphorus Building Gypsum

Preparation and Performance of Cement Mortar Reinforced by Modified Bamboo Fibers

Influences of pretreatment methods on the mechanical and environmental behaviors of PG-GGBS-LM ternary stabilizer

Effect of Mineral Admixtures on Physical, Mechanical, and Microstructural Properties of Flue Gas Desulfurization Gypsum-Based Self-Leveling Mortar

Optimization design and mechanical properties of multi-component ecological gelling materials

Evaluation of compressive strength and chloride permeability of cement-based materials with high-volume compound mineral admixtures

Performance of Green Binder Developed from Flue Gas Desulfurization Gypsum Incorporating Portland Cement and Large-Volume Fly Ash

Effect and Mechanism of Superplasticizers on Performance of Ultrafine Sulfoaluminate Cement-Based Grouting Materials

Compressive Strength and Microstructural Development of Cementitious Mixtures Incorporating Ultrafine Granulated Blast Furnace Slag

Use of recycled gypsum in the cement-based stabilization of very soft clays and its micro-mechanism

Study on the Strength and Micro Characteristics of Grouted Specimens with Different Superfine Cement Contents

Experimental Study on the Effect of Polycarboxylate Superplasticizer on the Performance of Cement-Based Grouting Materials

Effect and Mechanism of Superplasticizers on Microstructure and Properties of Ultrafine Sulfoaluminate Cement-Based Grouting Materials

Rheological Behavior and Strength Characteristics of Cement Paste and Mortar with Fly Ash and GGBS Admixtures

Mechanical Properties and Coagulation Characteristics of Flue Gas Desulfurization Gypsum-Based Polymer Materials

Mechanical and microstructural properties of cemented marine dredged clay with pre-hydrated ground granulated blast furnace slag