Abstract:As a surface-strengthening technology, electro-spark deposition (ESD) is widely used in the strengthening and repair of key components of high-end equipment. In this paper, a fusion and solidification model of ESD coating is established. The method of heat–fluid–solid interaction is adopted to simulate the material’s flow and fusion process in the droplet dropping into the molten pool. The distribution law of the coating-matrix material inside the coating was studied. Through the heat transfer between the molten material and the matrix material, the condensation and solidification process of the coating-matrix material is simulated, the temperature change in the coating area during the solidification process is analyzed, and the solidification law of the molten material is studied. The results show that the deposition time reaches 80 μs, and the content of electrode material at the bottom of the molten pool reaches 4.5%. The content of electrode material in the upper region of the material gushing out of the molten pool is higher than that in the bottom region. The material outside the molten pool solidifies first, and the molten material in the molten pool gradually solidifies from the bottom up; the shape of the solidification interface is similar to the boundary of the molten pool. Through the single-point deposition experiment of electro-spark deposition, the surface morphology of the deposition point was observed. The depth of the concave part of the contour can reach 16 μm. The difference between the two contour curves in the horizontal direction is not much; the error of the diameter is about 4%. The element distribution of the surface and the section of the deposition point are analyzed. The diffusion distance in the depth direction of the coating is about 4μm, and the transverse diffusion distance inside the coating is 364 μm. The error is 7.6% compared with the experimental results. The cross-section structure of the deposition point was observed, and the error between the experimental results and the simulation results in diameter is about 11%. It was found that the material distribution in the sedimentary area is basically consistent with the simulation results, and the simulation results are verified from the side.

Finite Element Numerical Simulation of EDM Surface Strengthening in Gas Medium of Stainless Steel 1Cr13

Experimental and Numerical Simulations of ELM-like Transient Damage Behaviors to Different Grade Tungsten and Tungsten Alloys

Research on Simulation of Coating Fusion and Solidification Process in Electro-Spark Deposition

EDM Surface Strengthening Research on Rubber Mold

Numerical Simulation of Thermal Field and Performance Study on H13 Die Steel-Based Wire Arc Additive Manufacturing

Analysis and simulation of micro electro discharge machining process

Finite-element simulation of semi-solid metal processing of tool steel encased in carbon steel

Numerical modeling from process to residual stress induced in resistance spot welding of DP980 steel

Numerical Simulation of Residual Stress and Deformation in Wire Arc Additive Manufacturing

Simulation on Surface Morphology Evolution of Metal Targets Irradiated by Intense Pulsed Electron Beam

Numerical simulation method of submerged arc surfacing process of rollers

Numerical Simulation Development and Computational Optimization for Directed Energy Deposition Additive Manufacturing Process

Thermal Analysis and Verification for Direct Metal Deposition of 0Cr18Ni9 Stainless Steel

Experimental and Numerical Investigation of CMT Wire and Arc Additive Manufacturing of 2205 Duplex Stainless Steel

Numerical Simulation of Arc and Metal Transfer in Arc Welding Based Additive Manufacturing Assisted by External Longitudinal Static Magnetic Field

Numerical simulation of thermal and stress fields for multilayer and multi-pass weaving WAAM of magnesium alloy

Research on hot deformation, dynamic recrystallization and numerical simulation of Fe–28Mn–10Al–1.5C–0.6V steel

Study of the effect of spark radius model upon the performance characteristics in EDM process

Numerical Simulation of Residual Stress Field Induced by Ultrasonic Shot Peening

Surface Nanocrystallization and Numerical Modeling of 316L Stainless Steel during Ultrasonic Shot Peening Process

Numerical Simulation and Experimental Verification of the Quenching Process for Ti Microalloying H13 Steel Used to Shield Machine Cutter Rings