Abstract:A single stage cryogenic liquid turbine is developed for replacing the Joule-Thompson valve and recovering energy from the liquefied air during throttling process in the large-scale internal compression air-separation unit, and evaluation of the impeller axial thrust at different conditions is essential for a reliable bearing design and stable operation. To predict the axial thrust load, a numerical model is established to simulate the turbine flow in a turbine stage environment, which includes the main flow domain (an asymmetrical volute, variable geometry nozzle, impeller, and diffuser), impeller front and back side gaps, and shaft seal leakage. Numerical simulation of flow is conducted by using the ANSYS-CFX. Flow characteristics in both main flow domain and impeller side gaps of the turbine stage are captured and analyzed. The axial thrust is then calculated based on the obtained pressure data in the impeller and its front and side gaps by using a direct integration approach.Flow behaviour in both main flow domain and impeller side gaps has been well exhibited by the numerical results. At the impeller back side gap inlet, the back flow is encountered even for design condition and it returns the impeller main flow stream; the impeller side gap flow has much influence on the axial thrust. To investigate influence of turbine operation condition on axial thrust, flow simulation is conducted at different mass flow rates and inlet pressure for the turbine stage, based on which the axial thrust is calculated. It is demonstrated from the obtained numerical results that the axial thrust increases as the inlet pressure increases and decreases as turbine flow rate increases. Geometry parametric study is conducted for the shaft seal clearances, which has demonstrated that the axial thrust is influenced largely by the clearance size and it decreases as the clearance grows.For the purpose of comparison, the empirical method is also used to predict the axial thrust load. The obtained results are compared to the numerical ones and evident deviation of the empirical from the numerical exists and the reason is that axial force components caused by the impeller main flow stream and its side gap flow are approximated very roughly in the empirical method.

Investigation Of Impeller Strength For A Cryogenic Liquid Turbiine

Numerical Investigation Of A Cryogenic Liquid Turbine Performance And Flow Behavior

Fluid-Thermal-Structural Analysis of Partial Admission Axial Impulse Turbines with Liquid Jet Impingement Cooling

Prediction of Axial Thrust Load Acting on a Cryogenic Liquid Turbine Impeller

Investigation of Flow-Induced Radial Force and Its Influence on Rotor Dynamics for a Cryogenic Liquid Turbine Expander

Numerical Study of Cavitating Behavior in A Cryogenic Liquid Turbine

Characterization of Loss, Temperature, and Stress on Partial Admission Axial Impulse Turbines with Liquid Jet Impingement Cooling

A FLUID-THERMAL ANALYSIS OF PARTIAL ADMISSION AXIAL TURBINES

Numerical Investigation of Impingement Heat Transfer on Smooth and Roughened Surfaces in a High-Pressure Turbine Inner Casing

Numerical Investigation On Sealing Behaviors Of An Extremely High-Speed Two-Stage Impellers Structure In Cryogenic Rockets

Investigating the Influence of Impeller Axial Thrust Balance Holes on the Flow and Overall Performance of a Cryogenic Liquid Turbine Expander

Swirling and cavitating flow suppression in a cryogenic liquid turbine expander through geometric optimization

Influence of Impeller Fairing Cone Geometry on Cavitating Flow Behavior in A Cryogenic Liquid Turbine Expander

Cavitation Suppression and Design Optimization in a Cryogenic Liquid Turbine Expander Based on Thermodynamic Cavitation and Entropy Production Analysis

Strength Design And Numerical Analysis Of Radial Inflow Turbine Impeller For A 100kw Microturbine

Numerical and Experimental Studies on Stability of Cryogenic Turbo-Expander with Protuberant Foil Gas Bearings

Design Of Cryogenic Centrifugal Compressor Stages With Heat Transfer Considerations

NUMERICAL INVESTIGATION OF IMPINGING-FILM HEAT TRANSFER AND FLOW CHARACTERISTICS OF TURBINE INNER CASING

Preliminary Design and Performance Analysis of a Radial Inflow Turbine for a Large-Scale Helium Cryogenic System

NUMERICAL STUDY ON THE FLOW FIELD ANALYSIS AND OPTIMIZATION OF TURBINE IN SUPERCRITICAL COMPRESSED AIR ENERGY STORAGE

Influence of Thermodynamic Effects on Rotor-Stator Cavity Flow in Liquid Oxygen Turbopump