Abstract:A compact and low-power consuming fiber-optic anemometer based on single-walled carbon nanotubes (SWCNTs) coated tilted fiber Bragg grating (TFBG) is presented. TFBG as a near infrared in-fiber sensing element is able to excite a number of cladding modes and radiation modes in the fiber and effectively couple light in the core to interact with the fiber surrounding mediums. It is an ideal in-fiber device used in a fiber hot-wire anemometer (HWA) as both coupling and sensing elements to simplify the sensing head structure. The fabricated TFBG was immobilized with an SWCNT film on the fiber surface. SWCNTs, a kind of innovative nanomaterial, were utilized as light-heat conversion medium instead of traditional metallic materials, due to its excellent infrared light absorption ability and competitive thermal conductivity. When the SWCNT film strongly absorbs the light in the fiber, the sensor head can be heated and form a "hot wire". As the sensor is put into wind field, the wind will take away the heat on the sensor resulting in a temperature variation that is then accurately measured by the TFBG. Benefited from the high coupling and absorption efficiency, the heating and sensing light source was shared with only one broadband light source (BBS) without any extra pumping laser complicating the system. This not only significantly reduces power consumption, but also simplifies the whole sensing system with lower cost. In experiments, the key parameters of the sensor, such as the film thickness and the inherent angle of the TFBG, were fully investigated. It was demonstrated that, under a very low BBS input power of 9.87 mW, a 0.100 nm wavelength response can still be detected as the wind speed changed from 0 to 2 m/s. In addition, the sensitivity was found to be -0.0346 nm/(m/s) under the wind speed of 1 m/s. The proposed simple and low-power-consumption wind speed sensing system exhibits promising potential for future long-term remote monitoring and on-chip sensing in practical applications.

Hot-wire Probe Based on Carbon Nanotube Strands

Highly Sensitive Hot-Wire Anemometry Based On Macro-Sized Double-Walled Carbon Nanotube Strands

Thermal Conductivity of A New Carbon Nanotube Analog: the Diamond Nanothread

Nanowire Thermometers.

Thermal Characterization of Microscale Conductive and Nonconductive Wires Using Transient Electrothermal Technique

Electrothermal Characterization of Single-Walled Carbon Nanotube (SWCNT) Interconnect Arrays

High Sensitivity Temperature Sensor Based on A Long, Suspended Single-Walled Carbon Nanotube Array

High Sensitivity Carbon Nanotubes Flow-Rate Sensors And Their Performance Improvement By Coating

Ultra High Thermal Resolution Scanning Probe Microscopy via Carbon Nanotube Tipped Thermal Probes

Non-contact T-type Raman Method for Measurement of Thermophysical Properties of Micro-/Nanowires

Quantitative Thermal Imaging of Single-Walled Carbon Nanotube Devices by Scanning Joule Expansion Microscopy.

Differential Multi-probe Thermal Transport Measurements of Multi-walled Carbon Nanotubes grown by Chemical Vapor Deposition

Carbon Nanotubes and Carbon Nanotube Structures Used for Temperature Measurement

Design and Test of Carbon Nanotube Biwick Structure for High-Heat-Flux Phase Change Heat Transfer

Raman measurement of heat transfer in suspended individual carbon nanotube

Measurements of Thermal Conductivity of Individual Carbon Nanotubes

The fabrication of nanoelectrodes based on a single carbon nanotube.

Thermal Characterization of Micro/nanoscale Conductive and Non-Conductive Wires Based on Optical Heating and Electrical Thermal Sensing

A Novel Low-Power-Consumption All-Fiber-Optic Anemometer with Simple System Design

Short-Hot-Wire Method for the Measurement of the Thermal Conductivity of A Fine Fibre

Characterization of Thermal Diffusivity of Micro/nanoscale Wires by Transient Photo-Electro-thermal Technique