Abstract:In a new pressurized water reactor nuclear power plant, the heat exchange tube bundle of the Moisture Separator Reheater (MSR) is a new designed staggered arrangement low helically finned-tube bundle. To investigation the thermal hydraulic characteristics of the Reheater part of MSR, the tube bundle test section was designed by using prototype tube and prototype arrangement of the new designed MSR. The experiment was carried out on the test section with steam cross-flowing outside the horizontal tube bundle, same conditions as MSR’ operation designing , and electrical heating in the tubes simulating the condensation heat release of the two phase-flow inside. A lot of experimental data on heat transfer and pressure drop were obtained in a broad experiment parameters range of wall heat flux density and steam temperature, pressure and Reynolds number. Based on the present data, empirical average heat transfer correlation and friction factor correlation were proposed for the outside average heat transfer and pressure drop. Comparisons and analysis between these experimental results and some of other investigations were made. The conclusions of this experimental investigation were given. The results are very useful to the design of the heat exchange tube bundle in the MSR, and the validations of the new design. However, experimental studies cannot adequately reveal the detail of flow characteristics, and suitable correlations for this fin geometry are very rare. Thus, numerical simulations should be performed to make up for the deficiency. To perform a detail understanding of the heat transfer and pressure drop characteristics, a three-dimensional geometry was carefully constructed and a fine mesh was generated. The flow across the tubes was assumed to be a steady, incompressible turbulent flow. RNG based – k turbulence model was chosen in the simulation. Nusselt number and Euler number of a wide range of Reynolds numbers (based on the steam velocity through the minimum flow area) from 4 1 10 to 4 8 10 were calculated by the CFD software ANSYS Fluent. The numerical results were compared with experiment results of the same fin geometry and tube configuration. Also, local flow behavior and local temperature distribution were obtained to show the detail flow features and heat transfer. The velocity and temperature distribution near the fin surface were discussed

Thermodynamic Calculation of Moisture Separator Reheater in Nuclear Power Plant

Thermal-Hydraulic Calculation and Analysis on Evaporator System of a 1000 MW Ultra-Supercritical Pulverized Combustion Boiler with Double Reheat

Experimental and numerical investigation of heat transfer and pressure drop in staggered arrangement helically finned-tube bundle

Numerical Investigation on Heat Transfer and Pressure Drop Characteristics of Moisture Separator Reheater with Porous Media Method

Heat Transfer Characteristics in Super-Low Finned-Tube Bundles of Moisture Separator Reheaters

Study on the reheater design used in the supercritical steam turbine power conversion cycle of MHTR

A Study of the Thermodynamic System Calculations for the Secondary Circuit of a Pressurized Water Reactor

ICOPE-15-C004 Thermal-hydraulic Analysis and Metal Temperature Computation for the Water Wall of a 1000MW Ultra Supercritical Tower Boiler with Double Reheat

Thermodynamic Analysis of a Modified System for a 1000 MW Single Reheat Ultra-Supercritical Thermal Power Plant

Investigation of Two-Phase Phenomena Occurring Within Moisture Separator Reheater High-Level Reactor Trips at the Maanshan Nuclear Power Plant

Performance Analysis of Membrane Separation Process for Water and Heat Recovery from Flue Gas

Study on Calculation Method for Partition of Heat Transfer in an Ultra-supercritical Boiler

Influence of Cooling Water Parameters on the Thermal Performance of the Secondary Circuit System of a Modular High-Temperature Gas-Cooled Reactor Nuclear Power Plant

Design study of heat transport and power conversion systems for micro molten salt reactor

Thermal Efficiency Optimization of a Modular High Temperature Gas-Cooled Reactor Plant by Extraction Steam Distribution

Numerical Calculation on Temperature Fields of Vertical Waterwall in Ultra-supercritical Boilers

Performance Analysis on Mechanical Vapor Recompression System

Thermal–hydraulic Calculation and Analysis of a 600 MW Supercritical Circulating Fluidized Bed Boiler with Annular Furnace

Steady Thermal Hydraulics Analysis for A Graphite-Moderated Channel Type Molten Salt Reactor

Experimental Investigations On Temperature Distribution And Heat Removal Capability Of Residual Heat Exchanger

Three Dimensional Neutronic/thermal-Hydraulic Coupled Simulation of MSR in Transient State Condition