Abstract:Stirling-type pulse tube cryocoolers (SPTCs) working at liquid-helium temperatures are attractive in space applications because they have advantages of high reliability, compactness, etc. However, the refrigeration efficiency is as low as 0.5% of Carnot efficiency or less. A method of increasing the cross-sectional area of the regenerator at the colder part is proposed in this paper, so as to reduce the heat-associated enthalpy flow at the cold end and improve the performance of the regenerative refrigerators at liquid-helium temperatures, and it is verified through experiments for the first time. Two kinds of variable cross-sectional structures are used in the experiments, which both increase the volume of the regenerator at the colder part. The no-load temperature of the refrigerator reaches 3.87 K, which is about 0.14 K lower than that of the refrigerator with a uniform cross-sectional regenerator under the same working conditions, and the coefficient of performance (COP) is increased by 66% at 4.2 K, and the precooling temperature is 16 K in this case. Theoretical analyses show that there are several reasons for reducing the heat-associated enthalpy flow at the cold end, including: (1). increase of the heat transfer area between the working fluid and the matrix; (2). increase of the total heat capacity of the matrix at the cold end. It is found that the lower the refrigeration temperature, the more serious the real gas effect, resulting in a more significant improvement. However, the increase in the cross-sectional area causes some side effects of reducing both the impedance of the regenerator and the flow rate of the working gas, resulting in a lower heat transfer coefficient. A smaller benefit is got as the refrigeration temperature rises, and the improvement of the COP tends to vanish at about 6 K. It is also found that the performance improvement is more significant when the regenerative efficiency is lower. This new method should provide a reference for further improving the performance of the regenerative refrigerator at liquid-helium temperatures.

Improved Design of Externally Pressurized Gas Journal Bearing in Cryogenic Helium Turbo-expander

Numerical and Experimental Studies on Stability of Cryogenic Turbo-Expander with Protuberant Foil Gas Bearings

Numerical analysis of the static performance of an annular aerostatic gas thrust bearing applied in the cryogenic turbo-expander of the EAST subsystem

Study on Dynamic Pressure Effect of Gas Bearings in Fuel Cell Vehicles

THE INFLUENCE OF NON-IDEAL EFFECTS OF ACTUATING MEDIUM ON THE PERFORMANCE OF A PLASTIC CRYOCOOLER

Essential Improvement of the JT Cryocooler Working at Liquid Helium Temperature for Space: Efficient and Lightweight

Aerodynamic and Thermal Analysis of Bump Type Gas Foil Thrust Bearing for Cryogenic Helium Turboexpander

Design of A Valved Moving Magnet Type Linear Compressor for A Joule-Thomson Cryocooler

Experimental Study on a Floating Scroll-Type Compressor Driving a Precooled JT Cryocooler

Effects of bearing clearance and supporting stiffness on performances of rotor-bearing system with multi-decked protuberant gas foil journal bearing

Characterization of an Embraco Oil-Free Linear Compressor for Driving JT Cryocoolers Working at Liquid Helium Temperature

Varying the Cross-Sectional Area of the Regenerator for Improving the Refrigeration Efficiency at Liquid-Helium Temperatures

Cooling Project Design for Magnetic Bearing of HTGR Helium Gas Turbine

Research on the Condition of Nonisothermal-based Lubrication Problem of the Externally Pressurized Gas Bearings

Optimal Design of Boundary Angle for Gas Foil Thrust Bearing Thermal Performance

Theoretical and experimental investigations on load-carrying capacity of separated gas foil thrust bearing

Off-Design Performance Research of an Axial Helium Compressor for Htgr-10 Power Conversion Unit

Numeral Simulation of Turbocharged End in Medium-pressure Cryogenic Turboexpander

Technical Design and Principle Test of Active Magnetic Bearings for the Turbine Compressor of Htr-10gt

Comparative studies on double-layered protuberant foil bearing and Hydresil foil bearing