Abstract:Poor interfacial adhesion and the aggregation of carbon nanotubes (CNTs) are important factors that restrict effective synthesis in CNTs-reinforced copper matrix composites (CMCs). Here, chemical unzipping and matrix-alloying (addition of Cr) methods were integrated to address these two limitations of CMCs. The CuCr matrix composite reinforced with partially-unzipped CNTs (PUCNTs) was manufactured using flake powder metallurgy and spark plasma sintering (SPS) processes. The effects of PUCNTs on microstructure, microhardness, electrical conductivity, and tribological properties of the composites were studied. The results showed that the in-situ interfacial carbides (Cr7C3 or Cr23C6) improved interfacial adhesion between PUCNTs and CuCr matrix. Additionally, the microhardness and tribological performances of PUCNTs/CuCr composites were obviously improved with increased concentrations of PUCNTs. When the PUCNTs content reached 8 vol%, the microhardness of the PUCNTs/CuCr composite was about 116% and 63% higher than that of unreinforced CuCr and CNTs/CuCr composite, respectively. The coefficient of friction and wear rate of the PUCNTs/CuCr composite were about 70% and 68% lower, respectively, than those of unreinforced CuCr. A balance was obtained between the electrical conductivity and tribological properties of the PUCNTs/CuCr composite. The results of this study show PUCNTs are better reinforcement fillers than CNTs, and suggest a new strategy for the fabrication of sliding electrical contact composites with high performance.

Unzipped Multiwalled Carbon Nanotubes for Mechanical Reinforcement of Polymer Composites

Unzipped multiwalled carbon nanotube oxide/multiwalled carbon nanotube hybrids for polymer reinforcement.

Functionalization of unzipped carbon nanotube via in situ polymerization for mechanical reinforcement of polymer

Reducing Dispersity of Mechanical Properties of Carbon Fiber/epoxy Composites by Introducing Multi-Walled Carbon Nanotubes

Carbon-nanotube-templated Carbon Nanofibers with Improved Mechanical Performance

Functionalization of Carbon Nanotubes by Corona‐Discharge Induced Graft Polymerization for the Reinforcement of Epoxy Nanocomposites

Synergistic effect of Mn 2+ with unzipped carbon nanotubes on enhancement of mechanical properties of polyamide 66

Extremely high reinforcement of high‐density polyethylene by low loading of unzipped multi‐wall carbon nanotubes

Kevlar Nanofiber-Functionalized Multiwalled Carbon Nanotubes for Polymer Reinforcement

PPTA-oligomer Functionalized Multiwalled Carbon Nanotubes Synthesized by "One-Pot" Method for Reinforcement of Polyvinyl Chloride

Enhancing the Mechanical Performance of Fiber‐Reinforced Polymer Composites Using Carbon Nanotubes as an Effective Nano‐Phase Reinforcement

Effects of the partially-unzipped carbon nanotubes on the microstructure and properties of CuCr matrix composites

Preparation and characterization of polyurethane/multiwalled carbon nanotube composites

Partially unzipping carbon nanotubes: A route to synchronously improve fracture strength and toughness of nanocomposites inspired by pinning effect of screw

Mechanical Properties and Reinforcing Mechanisms of Cementitious Composites with Different Types of Multiwalled Carbon Nanotubes

Functionalization of multi-walled carbon nanotubes with non-reactive polymers through an ozone-mediated process for the preparation of a wide range of high performance polymer/carbon nanotube composites

Enhanced Mechanical Properties of Prestressed Multi-Walled Carbon Nanotubes.

Application of Carbon Nanotubes from Waste Plastics As Filler to Epoxy Resin Composite

Surface Modification of Carbon Fiber for Enhancing the Mechanical Strength of Composites

Interfacially Reinforced Methylphenylsilicone Resin Composites by Chemically Grafting Multiwall Carbon Nanotubes Onto Carbon Fibers

Mechanical reinforcement of chitosan using unzipped multiwalled carbon nanotube oxides