Abstract:Studies on viscoelastic properties of two types of isotactic polypropylene (iPP-1 and iPP-2) and their composites filled with carbon nanotubes (CNTs) (CNTs/iPP composites) were carried out by using rheometer. The influences of viscoelastic properties on the melt extrusion behaviors of iPPs and CNTs/iPP composites were further investigated by using capillary rheometer. The rheological results demonstrate that at 200 C the viscosity and storage modulus G' for iPP-1 are obviously lower than that for iPP-2. The appearance of frequency-independent plateau of G' at low frequencies and solid-like elastic behaviors for the CNTs/iPP composites containing CNT mass fraction of 5 wt% indicate the formation of entangled CNT networks in the composites. Both iPPs and CNTs/iPP composites exhibit prominent shear-thinning behaviors and the composites exhibit relatively higher viscosities and shear stresses than their iPP counterparts. The extrudate distortion and die swell for CNTs/iPP composite melts decrease compared with iPPs due to the formation of CNT networks in the composites. Although the die swell can still be observed at the high applied shear rates for the CNTs/iPP composite with the relatively high viscoelastic iPP-2 as the matrix, an appreciable phenomenon of "die shrinkage" rather than the common "die swell" at the low applied shear rates is observed for this CNTs/iPP composite. More interesting, the particular "die shrinkage" phenomenon is observed at all the applied shear rates for the CNTs/iPP composite with the relatively low viscoelastic iPP-1 as the matrix. The above results can be explained by that the CNT networks in the composites under shear might be able to restrict the deformation and elastic relaxation of iPP chains,which have the relatively low viscoelastic properties.

The Effects Of Temperature And Roll Pressing On The Properties Of Ipp Sheets

Influence of Hot Press Molding Parameters on the Tensile Strength of Bamboo Fiber/PLA Composites

Effects of cold rolling on the tensile response of glassy polymers: Experiments and modeling

Crystallinity and Crystallographic Texture in Isotactic Polypropylene during Deformation and Heating

Real Time Synchrotron SAXS and WAXS Investigations on Temperature Related Deformation and Transitions of Β-Ipp with Uniaxial Stretching

Molecular Orientations and True Stress−Strain Relationship in Isotactic Polypropylene Film

Effect of Morphology Development on the Low‐temperature Tensile Properties of PP / POE Blends

Rheological Behavior Of Isotactic Polypropylene(Ipp) Melts In Supercooling State

Study on the effect of the molding process and service temperature on the mechanical properties and low‐velocity impact performance of the ultra‐high molecular weight polyethylene fiber laminates

The effect of material characteristics and mould parameters on the thermoforming of thick polypropylene sheets

The Influence of Pressure-Induced-Flow Processing on the Morphology, Thermal and Mechanical Properties of Polypropylene Blends

Effect of Hot-Pressing Process on Mechanical Properties of UHMWPE Fiber Non-Woven Fabrics

Morphology and Mechanical Behavior of Isotactic Polypropylene (ipp)/syndiotactic Polypropylene (spp) Blends and Fibers

Effect of the synergistic interaction of zinc adipate, hydrotalcite and ethylene propylene rubber on the performances of polypropylene

Competition of shearing and cavitation effects on the deformation behavior of isotactic polypropylene during stretching

Influence of strain rate and temperature on mechanical properties of carbon woven-ply PPS thermoplastic laminates under dynamic compression

Interplay between crystallization behaviors and extensional deformation of isotactic polypropylene and its blend with poly(ethylene-co-octene)

Effect of Strain Rate and Temperature on the Tensile Properties of Long Glass Fiber-Reinforced Polypropylene Composites

Structural Characteristics of Fibrillar Crystals in Uniaxially Stretched Isotactic Polypropylene Dominated by Temperature and Strain

β-Nucleation effects induced by long chain branching polypropylene

STUDIES ON INFLUENCES OF VISCOELASTIC PROPERTIES ON MELT EXTRUSION OF CARBON NANOTUBES-FILLED ISOTACTIC POLYPROPYLENE COMPOSITES