Abstract:ABSTRACTLarge amount of work has been published on the tacticity‐properties relationship of isotactic polypropylene (iPP). However, the stereo‐defect distribution dependence of morphology and mechanical properties of β‐nucleated iPP (β‐iPP) is still not clear. In this study, two different iPP resins (PP‐A and PP‐B) with similar average isotacticity but different uniformities of stereo‐defect distribution were selected, their β‐iPP injection molding specimens were prepared, and the morphology evolution and tensile behaviors were studied by means of differential scanning calorimetry (DSC), 2D wide‐angle X‐ray diffraction (2D‐WAXD) and scanning electron microscope (SEM). DSC results showed that with the same concentration of β‐nucleating agent (0.3 wt % WBG‐II), PP‐B with more uniform stereo‐defect distribution exhibited more amount of β‐phase than that of PP‐A with less uniform stereo‐defect distribution, indicating that PP‐B is more favorable for the formation of β‐phase. SEM results showed that PP‐B formed more amount of β‐crystals with relatively high structural perfection, while in PP‐A a mixed morphology of α‐ and β‐phase with obviously higher amount of structural imperfection emerges. The results of room‐temperature tensile test indicated that the yield peak width of PP‐B was obviously wider, and the elongation at break of PP‐B was higher than that of PP‐A, showing a better ductile of PP‐B. The morphology evolution results of SEM, 2D‐WAXD and DSC suggest that, a combination of lamellar deformation and amorphous deformation occurred in PP‐A, while only amorphous deformation mainly took place in PP‐B, which was thought to be the reason for the different tensile behaviors of the samples. In the production of β‐PP products via injection molding, the uniformity of stereo‐defect distribution was found to be an important factor. PP with more uniform distribution of stereo‐defect favors the formation of large amount of β‐phase with high perfection, which exhibit superior ductile property. The related mechanism was discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014, 131, 40027.

The effect of material characteristics and mould parameters on the thermoforming of thick polypropylene sheets

Improved Polypropylene Thermoformability through Polyethylene Layering

Effects of Process Parameters in Thermoforming of Unidirectional Fibre-Reinforced Thermoplastics

Effect of rapid heating cycle injection mold temperature on crystal structures, morphology of polypropylene and surface quality of plastic parts

Effect of Morphology Development on the Low‐temperature Tensile Properties of PP / POE Blends

Microstructural Evolution and Its Effect on Mechanical Properties of Isotactic Polypropylene by Shear Plastic Deformation at Elevated Temperatures

Morphology and Mechanical Behavior of Isotactic Polypropylene with Different Stereo-Defect Distribution in Injection Molding

Effect of Rapid Mold Heating on the Structure and Performance of Injection-Molded Polypropylene

Effects of Stereo-Defect Distribution on the Crystalline Morphology and Tensile Behavior of Isotactic Polypropylene Prepared by Compression Molding Process

The Formation of a Highly Oriented Structure and Improvement of Properties in PP/PA6 Polymer Blends during Extrusion-Stretching

The Characterization of Rheological Properties of Melt Grafting Polypropylene for Foaming

Formability and Failure Mechanisms of Continuous Glass Fiber-Reinforced Polypropylene Composite Laminates in Thermoforming Below the Melting Temperature

Fused deposition modeling of polypropylene-aluminium silicate dihydrate microcomposites

A Modeling Framework for the Thermoforming of Carbon Fiber Reinforced Thermoplastic Composites

Investigation on the Morphology and Tensile Behavior of Β‐nucleated Isotactic Polypropylene with Different Stereo‐defect Distribution

Designing 3D printable polypropylene: Material and process optimisation through rheology

Effect of processing parameters, antistiction coatings, and polymer type when injection molding microfeatures

Effects of Thermoforming Parameters on Woven Carbon Fiber Thermoplastic Composites

Crystallinity and mechanical properties of polypropylene products foamed by microcellular injection molding process

Effect of processing parameter changes on mechanical properties during injection molding: Amorphous versus semi‐crystalline materials

A Revisit to the Flow and Pressure Jointly Induced Thick Lamellae in Isotactic Polypropylene: A Synchrotron Radiation Small‐ and Wide‐angle X‐ray Scattering Study