Abstract:In order to investigate the heat and the mass transfer during pressure swing adsorption (PSA) for oxygen production and improve oxygen production efficiency, a gas-solid two-phase pressure swing adsorption model was established for the π-shaped centripetal radial flow adsorber (CP-π RFA). The energy model, the adsorption heat, and the particle diameter were comparatively studied using this model. The results show that the maximum temperature in the adsorbent bed during pressurization with air (PR) and high-pressure feed (AD) processes for the single-phase model are 309.19 K and 313.63 K, respectively. The highest oxygen mole fractions in the adsorbent bed during PR step and AD step using the single-phase model are 55.66% and 62.65%, respectively. Under the same operating conditions, the maximum temperature in the adsorbent bed during the PR and AD steps for the two-phase model are 302.27 K and 305.29 K, respectively. The highest oxygen mole fractions in the adsorbent bed during PR step and AD step using the two-phase model are 57.51% and 66.02%, respectively. For no-adsorption heat, the maximum temperatures are 293.5 K and 293.9 K, respectively, and the highest oxygen mole fractions in the adsorbent bed during the PR step and AD step with no-adsorption heat are 59.25% and 72.18%, respectively. However, the maximum temperature in the bed during the two steps with adsorption heat are 302.3 K and 305.3 K, respectively, and the highest oxygen mole fractions are 57.51% and 66.02%, respectively. As the particle diameter increases, the highest oxygen mole fraction of the outlet would decrease, while the oxygen flow rate and recovery would increase. The adsorbent with a particle diameter of 1.6 mm is the best size. The laws of the heat and the mass transfer in the adsorber can provide an important technical reference for CP-π RFA in the PSA for oxygen production.

Two-Dimensional Modeling of the Transport Phenomena in the Adsorber During Pressure Swing Adsorption Process

Simulation of Levulinic Acid Adsorption in Packed Beds Using Parallel Pore/Surface Diffusion Model

Modeling Axial Distributions of Adsorbent Particle Size and Local Voidage in Expanded Bed

Analysis of flow distribution in a horizontal-type molecular sieve adsorber

Two-Dimensional Modeling of Pressure Swing Adsorption (PSA) Oxygen Generation with Radial-Flow Adsorber

Study of Modeling for Fixed-Bed Adsorption Process and Simulation in Experimental CO Separation Through PSA

Modelling and Simulation of Two-Bed PSA Process for Separating H2 from Methane Steam Reforming

Study on variable mass flow laws in π-shaped centripetal radial flow adsorber

Non-isothermal simulation of pressure swing adsorption for separating oxygen from air

3-D Modeling Of Gas-Solid Two-Phase Flow In A Pi-Shaped Centripetal Radial Flow Adsorber

Heat and Mass Transfer Characteristics of the Gas−solid Two-Phase Model in a Π-Shaped Centripetal Radial Flow Adsorber

Pressure Swing Adsorption Models and Its Applications

3-D Modeling of Gas–Solid Two-Phase Flow in a π-Shaped Centripetal Radial Flow Adsorber

A Review of Numerical Research on the Pressure Swing Adsorption Process

Numerical analysis on mass transfer process of binary component air for two dimensional adsorption bed

THERMAL NON-EQUILIBRIUM MODELING OF COUPLED HEAT AND MASS TRANSFER IN BULK ADSORPTION SYSTEM OF POROUS MEDIA

Progress in numerical simulation and optimization of pressure swing adsorption process

Mechanism Modeling of Elevated Temperature Pressure Swing Adsorption Process for Pre-Combustion Co2 Capture

Study of adsorption performance of vertical radial flow dual-bed adsorber used in air sparation unit

Modeling Of Elemental Mercury Control By Sorbents From Simulated Flue Gases

Study of heat and mass transfer in two dimensional fixed-bed adsorption