Abstract:In the present study, high order porous Ti–Nb(50-x)-HA(x) (x = 0,10,20 wt %) composites have been fabricated for orthopedic application by using powder metallurgical route consisting temporary space alloying and rapid microwave sintering process. Structural porosity, elastic modulus, compressive strength, corrosion resistance, and in-vitro bioactivity of as-sintered Ti–Nb-HA composites were studied. Results showed that the reinforcement of the HA assists in the formation of structural porosity, which reduced the elastic modulus. Porous Ti–Nb (with HA 10–20% content) composite possessed 40–60% structural porosity with a pore size of 150–260 μm and exhibited elastic modulus in the range of 12.5–29 GPa (near to human bone 8–20 GPa), which overcome the problem of stress shielding. The as-sintered composite not only possessed low elastic modulus but also exhibit high compressive strength (205–395 MPa). The alloying of HA improved the corrosion resistance and the protective efficiency of Ti–40Nb-10HA and Ti–30Nb-20HA composites was measured 40% and 72%, respectively higher than the Ti–Nb composite. In-vitro biological evaluation tests confirmed that the developed composites are non-cytotoxic and porous structure provides a vehicle for cell adhesion and growth. Moreover, various biocompatible phases such as Ca3(PO4)2 (known as TCP), Ti5P3 and CaO were developed, which helped in cell proliferation and differentiation. High biological activities were found on the Ti–30Nb-20HA composite have when compared with the Ti–Nb and Ti–40Nb-10HA composite and could be used as a potential biomaterial for the various possible orthopedic applications.

Porous Ti/HA biocomposites for biomaterial applications

Research of Porous Ti/HA Bio-Composite Fabricated by Powder Metallurgical Method

Fabrication and Characterization of Titanium-Matrix Composite with 20 Vol% Hydroxyapatite for Use As Heavy Load-Bearing Hard Tissue Replacement

Fabrication and Characterization of Hydroxyapatite Reinforced with 20 Vol % Ti Particles for Use As Hard Tissue Replacement.

In vivo bioactivity of Ti/HA biocomposites fabricated by powder metallurgy methods

Mechanical and Biological Properties of Hydroxyapatite Reinforced with 40 Vol. % Titanium Particles for Use As Hard Tissue Replacement.

Mechanical and Corrosion Properties of Ti-35Nb-7Zr- X HA Composites Fabricated by Spark Plasma Sintering

Effects of Sn Content on the Microstructure, Mechanical Properties and Biocompatibility of Ti–Nb–Sn/hydroxyapatite Biocomposites Synthesized by Powder Metallurgy

Function-structure-integrated Ti-HA coatings on TiNbZr with enhanced mechanical properties and bioactivity prepared by spark plasma sintering

Microstructure and Properties of Ti35Nb2.5Sn5HA Biocomposites by Powder Metallurgy and Sintering

Microwave sintering of porous Ti–Nb-HA composite with high strength and enhanced bioactivity for implant applications

Microstructure and in Vitro Bioactivity of 50ti/ha Biocomposite

Microstructure and in Vitro Bioactivities of HA/Ti Composites Prepared by Hot Isostatic Pressing

HA/Ti composite for biomedical application by mechanical milling

Correlations Between the in Vitro and in Vivo Bioactivity of the Ti/HA Composites Fabricated by a Powder Metallurgy Method.

Tribological behavior and in vitro biocompatibility of powder metallurgical Ti–15Mo/HA composite for bone repair

Ti-Nb-Sn-Hydroxyapatite Composites Synthesized by Mechanical Alloying and High Frequency Induction Heated Sintering

Electrochemical Corrosion and Bioactivity of Ti-Nb-Sn-hydroxyapatite Composites Fabricated by Pulse Current Activated Sintering

Reinforcement of Hydroxyapatite Bioceramic by Addition of Ti3SiC2

Preparation and bioactive surface modification of the microwave sintered porous Ti-15Mo alloys for biomedical application

Hydroxyapatite-Bioglass-Titanium Biomaterials Used As Dense Bulk in Double-layer Biomimetic Composite