Abstract:The effect of sintering atmosphere (air and Ar) and temperature (1100, 1200, 1300 °C) on the microstructure, mechanical properties, and bioactivity of hydroxyapatite/tantalum (HA/Ta) composites were systematically investigated by pressureless sintering of the mixture of HA and Ta powders. It shows that the sintering atmosphere greatly impacts the phase composition and microstructure of the HA/Ta composites. The higher diffusion of atoms promotes shrinkage and causes deeper reaction fusion between the HA matrix and Ta, which improved the interfacial binding of the HA/Ta composites. The refined grain structure and improved interfacial binding obtained within the Ar atmosphere compared to the air atmosphere benefit the mechanical properties. The maximum bending strength and shrinkage observed for the composites sintered at 1300 °C in the Ar atmosphere are 27.24 MPa and 6.65%, respectively. The cell counting kit-8 (CCK-8) method was used to investigate the in vitro cytocompatibility of HA/Ta composites. The results revealed that the HA/Ta composites sintered with different conditions have no cytotoxicity. The simulated body fluid (SBF) soaking results showed that all of the studied composites possess desirable bioactivity, as demonstrated by their ability to form calcium-deficient carbonate apatite layer on the surfaces. For composites sintered at 1300 °C, the surface apatite layer coverage of the composites obtained in the Ar atmosphere was increased by 139.7% than the ones obtained in air, which confirmed an enhanced bioactive mineralization ability. The results indicated that the HA/Ta composites sintered at 1300 °C in Ar possess desirable mechanical properties and bioactivity. This work opens up the new possibility for preparing HA-based composites and is of great value in biomedical applications.This article has not yet been cited by other publications.

Microstructure and Properties of Ti35Nb2.5Sn5HA Biocomposites by Powder Metallurgy and Sintering

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Mechanical milling and its influence on microstructure and electric conductivity of high mass fraction TiC / Cu composites

Microwave sintering of porous Ti–Nb-HA composite with high strength and enhanced bioactivity for implant applications

Processing of Ti50Nb50−xHAx composites by rapid microwave sintering technique for biomedical applications

Characteristics of Ti-Nb-Mg alloy by powder metallurgy for biomedical applications

Function-structure-integrated Ti-HA coatings on TiNbZr with enhanced mechanical properties and bioactivity prepared by spark plasma sintering

In Situ Ti6Al4V/TiB Composites Prepared by Hydrogen-Assisted Sintering of Blends Containing TiH2 and Ball-Milled Ti+TiB2 Powders

Sintering Behavior and Mechanical Properties of Ti–TiBw Composites Prepared with Pre‐alloyed Ti–TiBw Composite Powders

In Situ Fabrication of Ti-xNb Alloys by Conventional Powder Metallurgy

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites

Microstructure, densification and mechanical properties of in situ TiBw/Ti2AlNb composites fabricated by spark plasma sintering

Machinable Ti3sic2/Hydroxyapatite Bioceramic Composites by Spark Plasma Sintering

Effect of spark plasma sintering temperature on the multi-scale microstructure evolution and mechanical properties of Ti 2 AlC/TiAl composites with network architecture

Fabrication of Hydroxyapatite/Tantalum Composites by Pressureless Sintering in Different Atmosphere

Fabrication of Nano-Sic_p/al Composite by High Energy Ball Milling

Hydroxyapatite Reinforced With Ti-Fe Particle: Correlation Between Composition, Microstructure And Mechanical Properties

Microstructural evolution during annealing of a powder metallurgical TiAl–Nb composite and its effect on mechanical properties

Tribological behavior and in vitro biocompatibility of powder metallurgical Ti–15Mo/HA composite for bone repair

Preparation and Properties of Hydroxyapatite-Ti composite Thin Films by Co-sputtering Method for Biocompatibility Applications