Abstract:The demands for high density, fine pitch interconnections in electronics systems has seen solder-based approaches for such interconnections miniaturized to the scale of tens of micro meters. At such a small scale, such 'micro joints' may contain only one or a few grains and the resultant mechanical behaviour may not be that for a polycrystalline aggregate, but rather for a single crystal. Since the ~-Sn matrix of SnAgCu solder has a contracted body-centred tetragonal (BCT) structure, such a solder grain is expected to demonstrate a considerably anisotropic behaviour. In such cases the reliability of a Phfree solder is strongly dependent on the local microstructural features, such as the size and orientation of the grains. This thesis presents the investigation of the evolution of microstructure within a joint or at the interface and, the influence of such microstructural features on the meso-scale mechanical behaviour of the Ph-free solder. It includes Evolution of the interface between a molten solder and the Cu substrate To form a joint, the solder alloy is heated and molten, wetting a solid under-bump metallization. After solidification, layers of brittle intermetallic compounds (IMCs) are formed at the interface. In this project, facilities were set up to obtain interfacial reactants at an arbitrary moment of the liquid/solid reaction. Formation and evolution ~ during reflow of SnCu IMCs at the interface between the molten SnAgCu alloy and the Cu UBM was captured and presented for the first time. Formation of phases and IMCs with the body of a liquid SnAgCu solder during solidification The formation behaviour of basic components for a SnAgCu grain (including Sn dendrites, AIDSn and Cu6Sns IMCs) during solidification was investigated. Relationships between the growth behaviour of these components and their internal lattice orientation were studied. The characteristic growth and coupling of AIDSn IMCs and the Sn matrix to form eutectics has been elaborated and presented in this study for - 1- the first time. Based on the results, the forming process of a eutectic SnAgCu grain under the non-equilibrioum solidification condition was illustrated; and major factors that determine the lattice-orientation, size and substructure of the grain were discussed. Meso- and Micro- scale mechanical behaviour of a SnAgCu solder joint To study the size effect on the microstructure, and subsequently, the meso-scale · mechanical behaviour, solder joints were manufactured with varying geometries. Shearing tests were performed·on these meso-scale joints. The results first demonstrated that the anisotropic characteristics of a SnAgCu grain play an important role in the mechanical behaviour of both a meso-scale solder joint and the adjacent interfacial IMCs. To further investigate the micro-scale deformation and damage mechanisms, micro-mechanical tests were preformed within a SnAgCu grain. Constitutive equations for a SnAgCu grain Based on the experimental results, a crystal model was established to describe the local microstructure-dependent mechanical behaviour. The constitutive equation was implemented by means of the finite element approach, and applied in solder joints of a Flip Chip (FC) package by a multi-scale method. To describe the crystal behaviour at the higher temperature, the model was improved to account for deformations due to vacancy diffusion and thermal expansion. This model was integrated by an implicit approach, and implemented in a full three dimension (3D) finite element (FE) model.

Microstructures of AgMeO electric contact materials by reactive synthesis and severe plastic deformation

In Situ TEM Study of Pulse-Enhanced Plasticity of Monatomic Metallic Glasses

Microstructure evolution and properties of Cu–Ag microcomposites with different Ag content

Research and Development on Microstructure, Properties and Alloying of Cu-Ag Filamentary Composites

Progress and Current Status in Research on Nanostructured Cu-Ag Microcomposites for Conductor Wires

Preparation and Properties of Bi Doped AgSnO2(12) Electrical Contact Materials

Effects of electromagnetic stirring and subsequent homogenization treatment on the microstructure and mechanical properties of Al70Zn10Mg10Cu5Si5 multi-component alloy

Effect of added Ag on plasticity enhancement of Au80Sn20 eutectic alloys

Study on the Mechanical Alloying Process for Preparing Ag/LSCO Electrical Contact Material

Effect of Ag Addition on the Hot Deformation, Constitutive Equations and Processing Maps of a Hot Extruded Mg-Gd-Y Alloy

Research Progress on the Microstructure Evolution Mechanisms of Al-Mg Alloys by Severe Plastic Deformation

Microstructure and hot deformation behavior of the Cu-Sn-Ni-Zn-Ti(-Y) alloy

Effect of preparing method of ZnO powders on electrical arc erosion behavior of Ag/ZnO electrical contact material

Microstructural Features and Mechanical Behaviour of Lead Free Solders for Microelectronic Packaging

Achieving high strain rate superplasticity in an Al-Cu-Li alloy processed by thermo-mechanical processing

Microstructure evolution and mechanical properties of Cu-3Ag-xZr alloys processed by equal channel angular pressing

Achieving high-strain-rate and low-temperature superplasticity in an ECAP-processed Mg-Y-Er-Zn alloy via Ag addition

Electrical Performance of Cu Doped AgSnO<sub>2</sub>In<sub>2</sub>O<sub>3</sub> Electrical Contacts Fabricated by Internal Oxidation

Quasi-Continuous Network Structure Greatly Improved the Anti-Arc-Erosion Capability of Ag/Y2O3 Electrical Contacts

Microstructure evolution and composition redistribution of FeCoNiCrMn high entropy alloy under extreme plastic deformation

Microstructure Evolution and Mechanical Properties of Mg-7Gd-3Y-1Nd-1Zn-0.5Zr Alloy