Abstract:It is widely recognized that the scandium addition to aluminum alloys is an effective way to improve the comprehensive properties. To the present, researchers are concentrated on Al-Mg alloys, for multicomponent Al-Zn-Mg-Cu alloy, the microscopic characterization of the alloy heat treatment has gained a high level of research interest. However, researches on the evolution of precipitate microstructure in controlled plastic deformation combined with the role played by Sc have received scant attention. In the present paper, a micro-alloyed Al-Zn-Mg-Cu-Sc-Zr alloy was prepared by adding 0.2% scandium. Based on mastering the two-stage homogenization treatment in the early stage, the alloy was subjected to equal channel angular extrusion deformation, and subsequently the microstructure, dislocation evolution and precipitation behavior were observed. It is revealed that after second pass deformation, the grains in the deformation-prone zone are obviously shortened by 31% on average along the cross-section direction, compared with the first pass. Following two passes deformation, Al 3 (Sc, Zr), Al 3 Zr and MgZn 2Â phases are formed within grains, inhibiting grain coarsening and recrystallization during deformation. With the introduction of plastic deformation, it is analyzed that the shadow lines with different depths and stacking faults with different structures in the interior of the phase. Also, the overall proportion of the recrystallized structure and substructure of the alloy increases with the increasing deformation. In addition, after secondary deformation, the scandium rich compounds at the trigeminal grain boundary are reduced, while the zirconium rich compounds are significantly increased. Therefore, the different diffusivity of Sc/Zr elements and the combined effect of controlled thermal deformation can be considered to prepare the Al 3 Sc (Al 3 Zr) with core-shell structure in the later stage.

Mechanism on annealing recrystallization of Al-Zn-Mg-Cu-Sc alloy

Plastic Deformation and Precipitation Characterization of Al-Zn-Mg-Cu Alloy Micro-Alloyed with Sc

Effect of minor Sc and Zr on recrystallization behavior and mechanical properties of novel Al–Zn–Mg–Cu alloys

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Dynamic recrystallization and precipitation behavior of a novel Sc, Zr alloyed Al-Zn-Mg-Cu alloy during hot deformation

Grain Refinement Mechanism at High Undercooling of Ni80Cu20 Alloy

Experimental Investigation on Recrystallization Mechanism of a Ni-base Single Crystal Superalloy

Microstructures and Properties of Al–Zn–Mg–Mn Alloy with Trace Amounts of Sc and Zr

Recrystallization behavior of an Al-Zn-Mg-Cu alloy during hot deformation and subsequent heat treatment

Effect of isothermal multidirectional compression on microstructure and mechanical properties of Al–Zn–Mg–Cu–Zr alloy with minor Sc addition

Kinetics and microstructural evolution during recrystallization of a single crystal superalloy

Si-mediated reassembly of interfacially segregated Sc atoms in an Al-Cu-Sc alloy exposed to high-temperature creep

Effect of Sc microalloying on microstructure evolution and mechanical properties of extruded Al-Zn-Mg-Cu alloys

Dynamic Recrystallization-Dependent High-Temperature Tensile Properties and Deformation Mechanisms in Al-Mg-Sc-Zr Alloys

Microstructure Evolution and Recrystallization Mechanisms of a Cu-Cr-Sn Alloy during Thermal Deformation Process

Microstructures and Properties Evolution of Spray-Deposited Al-Zn-Mg-Cu-Zr Alloys with Scandium Addition

Microstructures evolution and mechanical properties disparity in 2070 Al-Li alloy with minor Sc addition

Phase transformation from η phase to S phase at grain boundary during annealing in rapidly-solidified Al-Zn-Mg-Cu alloy

Investigation of deformation behavior and strain-induced precipitations in Al-Zn-Mg-Cu alloys across a wide temperature range

The influence of Sc solute partitioning on ductile fracture of Sc-microalloyed Al-Cu alloys

Effect of Minor Sc Addition on the Microstructure Evolution of Al–Cu–Li–Mg Alloy During Homogenization with Different Cooling Modes