Abstract:It is widely recognized that the scandium addition to aluminum alloys is an effective way to improve the comprehensive properties. To the present, researchers are concentrated on Al-Mg alloys, for multicomponent Al-Zn-Mg-Cu alloy, the microscopic characterization of the alloy heat treatment has gained a high level of research interest. However, researches on the evolution of precipitate microstructure in controlled plastic deformation combined with the role played by Sc have received scant attention. In the present paper, a micro-alloyed Al-Zn-Mg-Cu-Sc-Zr alloy was prepared by adding 0.2% scandium. Based on mastering the two-stage homogenization treatment in the early stage, the alloy was subjected to equal channel angular extrusion deformation, and subsequently the microstructure, dislocation evolution and precipitation behavior were observed. It is revealed that after second pass deformation, the grains in the deformation-prone zone are obviously shortened by 31% on average along the cross-section direction, compared with the first pass. Following two passes deformation, Al 3 (Sc, Zr), Al 3 Zr and MgZn 2Â phases are formed within grains, inhibiting grain coarsening and recrystallization during deformation. With the introduction of plastic deformation, it is analyzed that the shadow lines with different depths and stacking faults with different structures in the interior of the phase. Also, the overall proportion of the recrystallized structure and substructure of the alloy increases with the increasing deformation. In addition, after secondary deformation, the scandium rich compounds at the trigeminal grain boundary are reduced, while the zirconium rich compounds are significantly increased. Therefore, the different diffusivity of Sc/Zr elements and the combined effect of controlled thermal deformation can be considered to prepare the Al 3 Sc (Al 3 Zr) with core-shell structure in the later stage.

Microstructures and Properties Evolution of Spray-Deposited Al-Zn-Mg-Cu-Zr Alloys with Scandium Addition

Influence of Sc Content on the Microstructure and Mechanical Properties of Cast Al-2Li-2Cu-0.5Mg-0.2Zr Alloy

Influence of minor Sc additions on grain refinement and microstructure characteristics of a high Zn-containing Al-Zn-Mg-Cu-Zr alloy

Plastic Deformation and Precipitation Characterization of Al-Zn-Mg-Cu Alloy Micro-Alloyed with Sc

Effect of Sc microalloying on microstructure evolution and mechanical properties of extruded Al-Zn-Mg-Cu alloys

Microstructure and Mechanical Properties of Al–Si–Mg–Cu–Ti Alloy with Trace Amounts of Scandium

Effects of Sc Addition on the Microstructure and Mechanical Properties of Cast Al-3Li-1.5Cu-0.15Zr Alloy

Effect of Sc/Zr ratio on the microstructure and mechanical properties of new type of Al–Zn–Mg–Sc–Zr alloys

Microstructures evolution and mechanical properties disparity in 2070 Al-Li alloy with minor Sc addition

Microstructures and Properties of Al–Zn–Mg–Mn Alloy with Trace Amounts of Sc and Zr

Influence of Sc on microstructure and mechanical properties of Al–Si–Mg–Cu–Zr alloy

Effect of Sc contents on the mechanical properties and damping capacity of Al-Zn-Mg-Cu-Zr-Sc alloys with different grain structures

Microstructure and Mechanical Properties of Casting Al-3Li-2Mg-1Zn-0.1Zr Alloys Modified by Sc Additions

EFFECT OF Sc ON MICROSTRUCTURE AND PROPERTIES OF Al-Li-Cu-Mg-Zr ALLOY

Addition of Sc in Wire-Based Directed Energy Deposition of Al–Mg–Zn–Cu Alloy: Microalloying to Refine Grains and Improve Mechanical Properties

Effect of scandium on microstructure and mechanical properties of high zinc concentration aluminum alloys

Effects of Mg and Cu on Microstructures and Properties of Spray-Deposited Al-Zn-Mg-Cu Alloys

Effects of Zr,Ti and Sc Additions on the Microstructure and Mechanical Properties of Al-0.4Cu-0.14Si-0.05Mg-0.2Fe Alloys

Mechanical properties, corrosion behavior and microstructure evolution of zinc and scandium co-strengthened 5xxx alloy

Effect of Sc and Zr on Microstructure and Mechanical Properties of As‐Cast Al–Li–Cu Alloys

Effect of Sc and Zr Additions on Microstructures and Corrosion Behavior of Al-Cu-Mg-Sc-Zr Alloys