Abstract:The Field Programmable Gate Array (FPGA) structure poses several constraints that make the implementation of complex asynchronous circuits such as Time–Mode (TM) circuits almost unfeasible. In particular, in Programmable Logic (PL) devices, such as FPGAs, the operation of the logic is usually synchronous with the system clock. However, it can happen that a very high–performance specifications demands to abandon this paradigm and to follow an asynchronous implementative solution. The main driver forcing the use of programmable logic solutions instead of tailored Application Specific Integrated Circuits (ASIC), best suiting an asynchronous design, is the request coming from the research community and industrial R&D of fast–prototyping at low Non Recursive Engineering (NRE) costs. For instance in the case of a high–resolved Time–to–Digital Converter (TDC), a signal clocked at some hundreds of MHz implemented in FPGA allows implementing a TDC with resolution at ns. If a higher resolution is required, the signal frequency cannot be increased further and one of the aces up the designer’s sleeve is the propagation delay of the logic in order to quantize the time intervals by means of a so-called Tapped Delay–Line (TDL). This implementation of TDL–based TDC in FPGAs requires special attention by the designer both in making the best use of all available resources and in foreseeing how signals propagate inside these devices. In this paper, we investigate the implementation of a high–performance TDL–TDC addressed to 28–nm 7–Series Xilinx FPGA, taking into account the comparison between different technological nodes from 65–nm to 20–nm. In this context, the term high–performance means extended dynamic–range (up to 10.3 s), high–resolution and single–shot precision (up to 366 fs and 12 ps r.m.s respectively), low differential and integral non–linearity (up to 250 fs and 2.5 ps respectively), and multi–channel capability (up to 16).

Double sampling architecture for performing fine time interpolation within a limited logic density FPGA

A High-Throughput Vernier Time-to-Digital Converter on FPGAs with Improved Resolution Using a Bi-Time Interpolation Scheme

A High Resolution Time-to-digital-convertor Based on a Carry-Chain and DSP48E1 Adders in a 28-Nm Field-Programmable-gate-array

A Two-Stage Interpolation Time-to-Digital Converter Implemented in 20 and 28 N·m FGPAs

A High-Resolution Tdc Implemented In A 90nm Process Fpga

A Low-Cost FPGA-Based Coarse-Fine Counting Time-to-Digital Converter With External High-Precision Reference Clock

A High-Resolution TDC Design Based on Multistep Fine Time Measurement by Utilizing Delay-Adjustable Looped Carry Chains on FPGAs

A Multi-chain Measurements Averaging TDC Implemented in a 40 nm FPGA

A 5.5 ps Time-interval RMS Precision Time-to-Digital Convertor Implemented in Intel Arria 10 FPGA

Dynamic Sample Rate Acquisition System Based on Time-to-digital Converter Technology

High-Resolution Time-to-Digital Converters Implemented on 40-, 28-, and 20-Nm FPGAs

A 20ps resolution wave union FPGA TDC with on-chip real time correction

TwinPop: A Resource-Efficient and Highly Linear FPGA-Based Time-to-Digital Converter

Time-to-Digital Converter IP-Core for FPGA at State of the Art

A 1.15-Ps Bin Size and 3.5-Ps Single-Shot Precision Time-to-Digital Converter with On-Board Offset Correction in an FPGA

An Adaptive Downsampling FPGA-Based TDC Implementation for Time Measurement Improvement

A 19 ps Precision and 170 M Samples/s Time-to-Digital Converter Implemented in FPGA with Online Calibration

A Design of High Resolution One-Clock-Cycle TDC Based on FPGA

Two-Stage Clock-Free Time-to-Digital Converter Based on Vernier and Tapped Delay Lines in FPGA Device

A High-Precision 2.5-Ps RMS Time Synchronization for Multiple High-Speed Transceivers in FPGA

High-Performance Time-to-Digital Conversion on a 16-nm Ultrascale+ FPGA