Abstract:Indentation creep testing and uniaxial creep testing were carried out in this paper in order to set up the relationship between them. The aim of this work is to present a experimental validated method to determine the material creep parameters (nm, creep stress exponent; cm, creep factor, ε˙=cmσnm, ε˙, tensile creep strain rate at the steady state; σ, creep stress, usually from the uniaxial tensile testing) from the indentation creep testing. Aluminum alloy 2A12 was tested in this paper. Firstly, a set of indentation creep testing was carried out at 200°C with a flat cylindrical indenter. The net indentation creep stresses were between 905.4 and 1414.8MPa. The steady indentation creep rates in different indentation stresses were obtained, from which the indention creep parameters (d˙=cIσNnI, d˙, the indentation creep depth rate at the steady state; σN, the net section stress; nI, indentation stress exponent; cI, indentation factor) can be derived. The indentation creep testing was simulated by the finite element method. In order to validate the method, a set of uniaxial tensile creep testing was carried out at the same temperature, i.e. 200°C. From the uniaxial tensile creep results, the material creep parameters (ε˙=cmσnm) were also derived. It is shown that the stress exponent determined from indentation and uniaxial creep testing is same, respectively, at a same temperature. A method has been presented to set up the relationship between the indentation creep parameters (d˙=cIσNnI) and uniaxial creep parameters (ε˙=cmσnm) based on a conversion factor. With the indentation creep testing results in conjunction with finite element creep analysis, the material creep parameters (nmI-FEM and cmI-FEM) have also been derived. It can be concluded that the indentation creep testing can been used to determine the creep parameters (nm and cm). The most important conclusion is that the indentation creep exponent is equal to the material creep exponent, nm=nI.

Investigation of creep stress exponent of 80Au/20Sn solder by nanoindentation

Anand Parameter Test for Pb-Free Material SnAgCu and Life Prediction for a CSP

Experimental Determination and Modification of Anand Model Constants for Pb-Free Material 95.5Sn4.0ag0.5cu

Experimental and Statistical Study of the Fracture Mechanism of Sn96.5Ag3Cu0.5 Solder Joints via Ball Shear Test

Effective Acquisition of Elastoplastic and Creep Parameters of Lead-Free Solder Alloy from High-Temperature Micro-Indentation Eliminating the Size Effect

Quantification of Creep Strain in Small Lead-Free Solder Joints with the In-Situ Micro Electronic-Resistance Measurement

Study on Creep Characterization of Nano-Sized Ag Particle-Reinforced Sn–Pb Composte Solder Joints

Creep mechanism in characteristic orientation of Sn and Sn-1.8Ag by nanoindentation

Tensile creep behavior of Sn–Ag–Cu–Ni multicomponent lead-free solder alloy

Steady-state nanoindentation creep test on β-Sn: A modified constant contact pressure method

Indentation Size Effect of Stress Exponent and Hardness in Homogeneous Duplex Eutectic 80Au/20sn

Thermal Creep and Fracture Behaviors of the Lead-Free Sn–Ag–Cu–Bi Solder Interconnections under Different Stress Levels

In Situ Measuring Electronic-Resistance Strains of Sn-3.5Ag Solder Joints Creep

Thermal Fatigue and Creep Fracture Behaviors of a Nanocomposite Solder in Microelectronic/Optoelectronic Packaging

Shear creep behavior of Sn-3Ag-0.5Cu solder bumps in ball grid array

In-situ study of creep in Sn-3Ag-0.5Cu solder

Study of Crystallographic Creep Parameters of Nickel-Based Single Crystal Superalloys by Indentation Method

Experimental and numerical study of the method to determine the creep parameters from the indentation creep testing

Nanoindentation Study on Micromechanical Behaviors of Au–Ni–Sn Intermetallic Layers in Au–20Sn/Ni Solder Joints

Effect of Ni content on the creep properties of Cu/Sn–0.3Ag–0.7Cu/Cu solder micro-joints

Creep Behavior of Lead-free Electronic Solder Alloys