Abstract:A new type of scalable MFC was developed based on using alternating graphite fiber brush array anode modules and dual cathode modules in order to simplify construction, operation, and maintenance of the electrodes. The modular MFC design was tested with a single (two-sided) cathode module with a specific surface area of 29 m(2) m(-3) based on a total liquid volume (1.4 L; 20 m(2) m(-3) using the total reactor volume of 2 L), and two brush anode modules. Three different types of spacers were used in the cathode module to provide structural stability, and enhance air flow relative to previous cassette (combined anode-cathode) designs: a low-profile wire spacer; a rigid polycarbonate column spacer; and a flexible plastic mesh spacer. The best performance was obtained using the wire spacer that produced a maximum power density of 1100 +/- 10 mW m(-2) of cathode (32 +/- 0.3 W m-3 based on liquid volume) with an acetate-amended wastewater (COD = 1010 +/- 30 mg L-1), compared to 1010 +/- 10 mW m(-2) for the column and 650 +/- 20 mW m(-2) for the mesh spacers. Anode potentials were unaffected by the different types of spacers. Raw domestic wastewater produced a maximum of 400 +/- 8 mWm(-2) under fed batch conditions (wire-spacers), which is one of the highest power densities for this fuel. Over time the maximum power was reduced to 300 +/- 10 mW m(-2) and 275 +/- 7 mW m(-2) for the two anode compartments, with only slightly less power of 250 +/- 20 mW m(-2) obtained under continuous flow conditions. In fixed-resistance tests, the average COD removal was 57 +/- 5% at a hydraulic retention time of 8 h. These results show that this modular MFC design can both simplify reactor construction and enable relatively high power generation from even relatively dilute wastewater.

[Electricity Generation Using the Packing-Type Microbial Fuel Cells].

Electricity Generation And Microbial Community Changes In Microbial Fuel Cells Packed With Different Anodic Materials

Characteristic in electricity-generation and wastewater-treatment by the two-cylinder microbial fuel cells

Power Generation by Packed-Bed Air-Cathode Microbial Fuel Cells

Effect of Anode Thickness on Electricity Generation of Packing-type Microbial Fuel Cell

High‐Performance Carbon Anode Derived from Sugarcane for Packed Microbial Fuel Cells

Enhanced electricity generation and storage by nitrogen-doped hierarchically porous carbon modification of the capacitive bioanode in microbial fuel cells

Effect of Electricity on Microbial Community of Microbial Fuel Cell Simultaneously Treating Sulfide and Nitrate

A novel pilot-scale stacked microbial fuel cell for efficient electricity generation and wastewater treatment.

Scalable air cathode microbial fuel cells using glass fiber separators, plastic mesh supporters, and graphite fiber brush anodes.

Electricity generation in a membrane-less microbial fuel cell with down-flow feeding onto the cathode

Influence of Current Collecting Methods on Performance of Packing-type Microbial Fuel Cell

High-Capacitance Manganese Dioxide Oxide/Carbon Nanotube/Carbon Felt as a Bioanode for Enhanced Energy Output in Microbial Fuel Cells

Power generation using carbon mesh cathodes with different diffusion layers in microbial fuel cells

Microbial fuel cells with an integrated spacer and separate anode and cathode modules

Electricity Production by an Overflow-Type Wetted-Wall Microbial Fuel Cell.

Modification of carbon based cathode electrode in a batch-type microbial fuel cells

Scale-up and stack performance of single-chamber microbial fuel cells with activated carbon air cathodes

Microbial Community Analysis in Biocathode Microbial Fuel Cells Packed with Different Materials

A miniaturized microbial fuel cell with three-dimensional graphene macroporous scaffold anode demonstrating a record power density of over 10 000 W m(-3) .

Electricity Generation from Organic Wastewater Using a Continuous-Flow Single Chamber Microbial Fuel Cell